Yamaha PSR-630 Owner's Manual - Page 157
Omni Off Recive Only Control Number = 7ch, Data Value = 0
View all Yamaha PSR-630 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 157 highlights
,Q,Q,Q,Q,Q,Q,Q,Q,Q,Q,Q,QMIDI ,QData Fo,Qrmat • ATTACK TIME applies adjustment to the envelope attack time set by the voice. This parameter specifies relative change with the value of 64 producing 0 adjustment. • BRIGHTNESS applies adjustment to the cut-off frequency set by the voice. This parameter specifies relative change with the value of 64 producing 0 adjustment. Lower voices produce a softer sound. For some voices the effective parameter range is narrower than the legal parameter range. (3-2) CHANNEL MODE MESSAGES STATUS 1011nnnn (BnH) CONTROL NUMBER 0ccccccc CONTROL VALUE 0vvvvvvv n = 0 - 15 VOICE CHANNEL NUMBER c = CONTROL NUMBER v = DATA VALUE (3-2-1) ALL SOUND OFF (Recive only) (CONTROL NUMBER = 78H , DATA VALUE = 0) Switches off all sound from the channel. Does not reset Note On and Hold On conditions established by Channel Messages. (3-2-2) RESET ALL CONTROLLERS (Recive only) (CONTROL NUMBER = 79H , DATA VALUE = 0) Resets controllers as follows. PITCH BEND CHANGE AFTER TOUCH MODULATION EXPRESSION SUSTAIN SOSTENUTO SOFT PEDAL NRPN RPN PORTAMENT CONTROL PORTAMENTO 0 (Center) 0 (min.) 0 (min.) 127 (max.) 0 (off) 0 (off) 0 (off) Sets number to null. (Internal data remains unchanged) Sets number to null. (Internal data remains unchanged) Resets portamento source note number 0 (off) (3-2-3) ALL NOTES OFF (Recive only) (CONTROL NUMBER = 7BH , DATA VALUE = 0) Switches off all of the channel's "on" notes. However, any notes being held by SUSTAIN or SOSTENUTO continue to sound until SUSTAIN/SOSTENUTO goes off. (3-2-4) OMNI OFF (Recive only) (CONTROL NUMBER = 7CH , DATA VALUE = 0) Same processing as for All Notes Off. (3-2-5) OMNI ON (Recive only) (CONTROL NUMBER = 7DH , DATA VALUE = 0) Same processing as for All Notes Off. Omni On is not executed. (3-2-6) MONO (Recive only) (CONTROL NUMBER = 7EH , DATA VALUE = 0) Same processing as for All Notes Off. If the 3rd byte is in a range of 0-16 the corresponding channel will be changed to Mode 4 (m=1). (3-2-7) POLY (Recive only) (CONTROL NUMBER = 7FH , DATA VALUE = 0) Same processing as for All Sounds Off and the corresponding channel will be changed to Mode 3. (3-3) REGISTERED PARAMETER NUMBER (RPN) STATUS 1011nnnn (BnH) n = 0 - 15 VOICE CHANNEL NUMBER RPN LSB 01100100 (64H) RPN LSB NUMBER 0ppppppp p = RPN LSB(refer to the list below) RPN MSB 01100101 (65H) RPN MSB NUMBER 0qqqqqqq q = RPN MSB(refer to the list below) DATA ENTRY MSB 00000110 (06H) DATA VALUE 0mmmmmmm m = Data Value DATA ENTRY LSB 00100110 (26H) DATA VALUE 0lllllll l = Data Value First appoints the parameter for RPN MSB/LSB, then sets the parameter value for data entry MSB/LSB. RPN D.ENTRY LSB MSB MSB LSB PARAMETER NAME DATA RANGE 00H 00H mmH - PITCH BEND SENSITIVITY 00H - 18H (0 - 24 semitones) 01H 00H mmH llH FINE TUNE {mmH,llH} = {00H,00H} - {40H,00H} - {7FH,7FH} (-8192*100/8192) - 0 - (+8192*100/8192) 02H 00H mmH - COARSE TUNE 28H - 40H - 58H (-24 - 0 - +24 semitones) 7FH 7FH - - NULL Clears the current RPN number setting. Does not change the internal parameter settings. (3-4) NON-REGISTERED PARAMETER NUMBER (NRPN) (Recive only) STATUS 1011nnnn (BnH) n = 0 - 15 VOICE CHANNEL NUMBER NRPN LSB 01100010 (62H) NRPN LSB NUMBER 0ppppppp p = NRPN LSB(refer to the list below) NRPN MSB 01100011 (63H) NRPN MSB NUMBER 0qqqqqqq q = NRPN MSB(refer to the list below) DATA ENTRY MSB 00000110 (06H) DATA VALUE 0mmmmmmm m = Data Value First appoints the parameter for NRPN MSB/LSB, then sets the parameter value for data entry MSB/LSB. NRPN D.ENTRY MSB LSB MSB LSB 01H 08H mmH - 01H 09H mmH - 01H 0AH mmH - 01H 20H mmH - 01H 21H mmH - 01H 63H mmH - 01H 64H mmH - 01H 66H mmH - 14H rrH mmH - 15H rrH mmH - 16H rrH mmH - 17H rrH mmH - 18H rrH mmH - 19H rrH mmH - 1AH rrH mmH - 1CH rrH mmH - 1DH rrH 1EH rrH 1FH rrH mmH - mmH - mmH - PARAMETER NAME DATA RANGE VIBRATO RATE 00H - 40H - 7FH (-64 - 0 - +63) VIBRATO DEPTH 00H - 40H - 7FH (-64 - 0 - +63) VIBRATO DELAY 00H - 40H - 7FH (-64 - 0 - +63) FILTER CUTOFF FREQUENCY 00H - 40H - 7FH (-64 - 0 - +63) FILTER RESONANCE 00H - 40H - 7FH (-64 - 0 - +63) EG ATTACK TIME 00H - 40H - 7FH (-64 - 0 - +63) EG DECAY TIME 00H - 40H - 7FH (-64 - 0 - +63) EG RELEASE 00H - 40H - 7FH (-64 - 0 - +63) DRUM FILTER CUTOFF FREQ. 00H - 40H - 7FH (-64 - 0 - +63) DRUM FILTER RESONANCE 00H - 40H - 7FH (-64 - 0 - +63) DRUM AEG ATTACK RATE 00H - 40H - 7FH (-64 - 0 - +63) DRUM AEG DECAY RATE 00H - 40H - 7FH (-64 - 0 - +63) DRUM PITCH COARSE 00H - 40H - 7FH (-64 - 0 - +63) DRUM PITCH FINE 00H - 40H - 7FH (-64 - 0 - +63) DRUM LEVEL 00H - 7FH (0 - max.) DRUM PANPOT 00H ,01H - 40H - 7FH (random,left - center - right) DRUM REVERB SEND LEVEL 00H - 7FH (0 - max.) DRUM CHORUS SEND LEVEL 00H - 7FH (0 - max.) DRUM VARIATION SEND LEVEL 00H - 7FH (0 - max.) The MSG14H-1FH (for drums) message is accepted as long as the channel is set with a drum voice. rrH : drum instrument note number (3-5) SYSTEM REALTIME MESSAGES (3-5-1) MIDI CLOCK STATUS 11111000 (F8H) Transmission: 96 clocks per measure are transmitted. Reception: If the instrument's clock is set to external, after FAH is received from the external device the instrument's clock will sync with the 96 beats per measure received from the external device. Decides whether the internal clock, or Timing Clocks received via the MIDI IN will be used. (3-5-2) START STATUS 11111010 (FAH) Transmission: Transmitted when instrument's Rhythm or Song playback is started. Reception: Depending upon the condition, Rhythm, Song Playback, or Song Rec will start. (3-5-3) STOP STATUS 11111100 (FCH) Transmission: Transmitted when instrument's Rhythm or Song playback is stopped. Reception: Depending upon the condition, Rhythm, Song Playback, or Song Rec will stop. (3-5-4) ACTIVE SENSING STATUS 11111110 (FEH) Transmission: Transmitted approximately once every 200msec. Reception: Sensing is started once this Code is received. If Status or Data is not received within 400ms, the MIDI Receive Buffer will be cleared, and all notes, including those being sustained, will be cut OFF. Also, all control values will be reset to their factory defaults. (3-6) SYSTEM EXCLUSIVE MESSAGE (3-6-1) YAMAHA MIDI FORMAT (3-6-1-1) SECTION CONTROL binary hexadecimal 11110000 F0 Exclusive status 01000011 43 YAMAHA ID 01111110 7E Style 00000000 00 0sssssss SS Switch No. 00H : INTRO A 01H~07H : INTRO B 08H : MAIN A 09H~0FH : MAIN B 10H : FILL IN AA 11H~17H : FILL IN BB 18H : FILL IN AB 19H~1FH : FILL IN BA 20H : ENDING A 21H~27H : ENDING B 0ddddddd DD Switch On/Off : 00H (Off),7FH (On) 11110111 F7 End of Exclusive When an ON code is received, the appointed section will be changed. 155