Home » ZyXEL Manuals » Networking » ZyXEL MAX318M » Manual Viewer

ZyXEL MAX318M User Guide - Page 152

Before you Begin, Type Of Service ToS, DiffServ, Speed Dial

Get ZyXEL MAX318M PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 152 highlights

Chapter 9 The VoIP General Screens Type Of Service (ToS) Network traffic can be classified by setting the ToS (Type Of Service) values at the data source (for example, at the WiMAX Device) so a server can decide the best method of delivery, that is the least cost, fastest route and so on. The ToS field is consist of 8 bits. The first 3 bits indicate the priority of the packet. DiffServ DiffServ is a class of service (CoS) model that marks packets so that they receive specific per-hop treatment at DiffServ-compliant network devices along the route based on the application types and traffic flow. Packets are marked with DiffServ Code Points (DSCPs) indicating the level of service desired. This allows the intermediary DiffServ-compliant network devices to handle the packets differently depending on the code points without the need to negotiate paths or remember state information for every flow. In addition, applications do not have to request a particular service or give advanced notice of where the traffic is going. DiffServ uses the first 6 bits of the 8-bit ToS value so that it can be backward compatible with nonDiffServ compliant but ToS-enabled network device. See Section 9.6.1 on page 156 for more information. SIP The Session Initiation Protocol (SIP) is an application-layer control (signaling) protocol that handles the setting up, altering and tearing down of voice and multimedia sessions over the Internet. SIP signaling is separate from the media for which it handles sessions. The media that is exchanged during the session can use a different path from that of the signaling. SIP handles telephone calls and can interface with traditional circuit-switched telephone networks. RTP When you make a VoIP call using SIP, the RTP (Real time Transport Protocol) is used to handle voice data transfer. See RFC 1889 for details on RTP. Speed Dial Speed dial provides shortcuts for dialing frequently used phone numbers. You can map a phone number to a self-defined key(s) and then use that key(s) to call the phone number. For example, you can map 123456 to #01. When you press #01 it means that you press 123456. 9.1.2 Before you Begin • Ensure that you have all of your voice account information on hand. If not, contact your voice account service provider to find out which settings in this chapter you should configure in order to use your telephone with the WiMAX Device. • Connect your WiMAX Device to the Internet, as described in the Quick Start Guide. If you have not already done so, then you will not be able to test your VoIP settings. 152 WiMAX Device Configuration User's Guide

Section	Page
WiMAX CPE Series	1
About This User's Guide	3
Document Conventions	4
Safety Warnings	6
Contents Overview	7
Table of Contents	9
User’s Guide	15
Introduction to the Series	17
1.1 About Your WiMAX Device	17
1.1.1 WiMAX Internet Access	18
1.1.2 Models with Phone Ports	18
1.1.3 Models with WiFi	19
1.2 Good Habits for Managing the WiMAX Device	19
Introduction to the Web Configurator	20
2.1 Overview	20
2.1.1 Accessing the Web Configurator	20
2.1.2 Saving and Canceling Changes	21
2.1.3 Working with Tables	21
2.2 The Main Screen	22
Setup Wizard	25
3.1 Overview	25
3.1.1 Welcome to the Setup Wizard	25
3.1.2 LAN Settings	26
3.1.3 WiMAX Frequency Settings	27
3.1.4 WiMAX Authentication Settings	28
3.1.5 VoIP Settings	30
3.1.6 WLAN Settings	32
3.1.7 Setup Complete	34
Tutorials	35
4.1 Overview	35
4.2 WiMAX Connection Settings	35
4.3 Setting Up a Small Network for the LAN	36
4.4 Making a Telephone Call Over the Internet	38
4.4.1 Configure Your SIP Account	38
4.5 Blocking Web Access from the WiMAX Device	40
4.6 Restricting Wireless Access to the WiMAX Device	40
4.7 Allowing Internet Users to use Internal Servers	42
4.8 Access the WiMAX Device with a Domain Name	44
4.8.1 Registering a DDNS Account on www.dyndns.org	45
4.8.2 Configuring DDNS on Your WiMAX Device	46
4.8.3 Testing the DDNS Setting	46
4.9 Configuring Static Route for Routing to Another Network	46
4.10 Remotely Managing Your WiMAX Device	48
4.11 Changing Certificate to Communicate with Other Networks	49
4.12 Using Virtual Networks	50
4.12.1 Scenario 1	51
4.12.2 Scenario 2	52
4.12.3 Scenario 3	54
4.12.4 Scenario 4	56
4.12.5 Scenario 5	58
Technical Reference	61
System Status	63
5.1 Overview	63
5.2 System Status	63
WiMAX	67
6.1 Overview	67
6.1.1 What You Need to Know	67
6.2 Connection Settings	70
6.3 Frequency Settings	72
6.4 Authentication Settings	74
6.5 Channel Plan Settings	77
6.6 CAPL Settings	79
6.6.1 CAPL Settings: Add	80
6.7 RAPL Settings	81
6.8 Home NSP Settings	82
6.9 Connect	83
6.10 Wide Scan	85
6.11 Link Status	87
6.12 Link Statistics	88
6.13 Connection Info	89
6.14 Service Flow	89
Network Setting	91
7.1 Overview	91
7.1.1 What You Need to Know	91
7.2 WAN	94
7.3 PPPoE	96
7.4 GRE	97
7.5 EtherIP	98
7.6 IP	98
7.7 DHCP	99
7.8 WLAN	100
7.9 WPS	102
7.10 MAC Address Filter	103
7.11 Static Route	104
7.12 Static Route Add	104
7.13 RIP	105
7.14 Port Forwarding	107
7.14.1 Port Forwarding Wizard	108
7.15 Port Trigger	108
7.15.1 Port Trigger Wizard	110
7.15.2 Trigger Port Forwarding Example	111
7.16 DMZ	111
7.17 ALG	112
7.18 QoS	113
7.19 UPnP	113
7.19.1 Installing UPnP in Windows XP	114
7.19.2 Web Configurator Easy Access	118
7.20 VLAN	119
7.21 DDNS	121
7.22 IGMP Proxy	123
7.23 Content Filter	123
Security	125
8.1 Overview	125
8.1.1 What You Need to Know	125
8.2 IP Filter	125
8.3 MAC Filter	126
8.4 DDOS	127
8.5 PPTP VPN Server	129
8.6 PPTP VPN Client	130
8.7 PPTP VPN Client: Add	131
8.8 L2TP VPN Server	133
8.9 L2TP VPN Client	135
8.10 L2TP VPN Client: Add	135
8.11 IPSec VPN	137
8.11.1 IPSec VPN: Add	139
8.12 Technical Reference	144
8.12.1 IPSec Architecture	144
8.12.2 Encapsulation	145
8.12.3 IKE Phases	146
8.12.4 Negotiation Mode	147
8.12.5 IPSec and NAT	147
8.12.6 VPN, NAT, and NAT Traversal	148
8.12.7 ID Type and Content	148
8.12.8 Pre-Shared Key	150
8.12.9 Diffie-Hellman (DH) Key Groups	150
The VoIP General Screens	151
9.1 VoIP Overview	151
9.1.1 What You Need to Know	151
9.1.2 Before you Begin	152
9.2 Media	153
9.3 QoS	154
9.4 SIP Settings	155
9.5 Speed Dial	155
9.6 Technical Reference	156
9.6.1 DSCP and Per-Hop Behavior	156
The VoIP Account Screens	157
10.1 Overview	157
10.1.1 What You Need to Know	157
10.2 Status	160
10.3 Server	161
10.4 SIP	163
10.5 Feature	165
10.6 Dialing	166
10.7 FAX	167
10.8 Technical Reference	167
10.8.1 SIP Call Progression with Session Timer	167
10.8.2 SIP Client Server	170
The VoIP Line Screens	171
11.1 Overview	171
11.1.1 What You Need to Know	171
11.2 Phone	172
11.3 Voice	172
11.4 Region	173
Maintenance	175
12.1 Overview	175
12.1.1 What You Need to Know	175
12.2 Password	180
12.3 HTTP	181
12.4 Telnet	181
12.5 SSH	182
12.6 SNMP	183
12.7 CWMP	183
12.8 OMA-DM	185
12.9 Date/Time	187
12.10 Time Zone	187
12.11 Upgrade File	188
12.11.1 The Firmware Upload Process	189
12.12 Upgrade Link	189
12.13 CWMP Upgrade	189
12.14 Backup/Restore	190
12.15 Restore	190
12.15.1 The Restore Configuration Process	191
12.16 Factory Defaults	191
12.17 Log Setting	192
12.18 Log Display	192
12.19 Network Test	193
12.20 Traceroute	194
12.21 About	194
12.22 Reboot	195
Troubleshooting	197
13.1 Power, Hardware Connections, and LEDs	197
13.2 WiMAX Device Access and Login	198
13.3 Internet Access	199
13.4 Wireless Internet Access (for Models with WiFi)	201
13.5 Phone Calls and VoIP (for Models with Phone Ports)	201
13.6 Reset the WiMAX Device to Its Factory Defaults	202
13.6.1 Pop-up Windows, JavaScript and Java Permissions	202
Product Specifications	203
WiMAX Security	207
Importing Certificates	211
Common Services	237
Open Software Announcements	241
Legal Information	277

Match case Limit results 1 per page

Chapter 9 The VoIP General Screens

WiMAX Device Configuration User’s Guide

152

Type Of Service (ToS)

Network traffic can be classified by setting the ToS (Type Of Service) values at the data source (for

example, at the WiMAX Device) so a server can decide the best method of delivery, that is the least

cost, fastest route and so on. The ToS field is consist of 8 bits. The first 3 bits indicate the priority of

the packet.

DiffServ

DiffServ is a class of service (CoS) model that marks packets so that they receive specific per-hop

treatment at DiffServ-compliant network devices along the route based on the application types

and traffic flow. Packets are marked with DiffServ Code Points (DSCPs) indicating the level of

service desired. This allows the intermediary DiffServ-compliant network devices to handle the

packets differently depending on the code points without the need to negotiate paths or remember

state information for every flow. In addition, applications do not have to request a particular service

or give advanced notice of where the traffic is going.

DiffServ uses the first 6 bits of the 8-bit ToS value so that it can be backward compatible with non-

DiffServ compliant but ToS-enabled network device. See

Section 9.6.1 on page 156

for more

information.

SIP

The Session Initiation Protocol (SIP) is an application-layer control (signaling) protocol that handles

the setting up, altering and tearing down of voice and multimedia sessions over the Internet. SIP

signaling is separate from the media for which it handles sessions. The media that is exchanged

during the session can use a different path from that of the signaling. SIP handles telephone calls

and can interface with traditional circuit-switched telephone networks.

RTP

When you make a VoIP call using SIP, the RTP (Real time Transport Protocol) is used to handle voice

data transfer. See RFC 1889 for details on RTP.

Speed Dial

Speed dial provides shortcuts for dialing frequently used phone numbers. You can map a phone

number to a self-defined key(s) and then use that key(s) to call the phone number. For example,

you can map 123456 to #01. When you press #01 it means that you press 123456.

9.1.2

Before you Begin

•

Ensure that you have all of your voice account information on hand. If not, contact your voice

account service provider to find out which settings in this chapter you should configure in order

to use your telephone with the WiMAX Device.

•

Connect your WiMAX Device to the Internet, as described in the Quick Start Guide. If you have

not already done so, then you will not be able to test your VoIP settings.