Canon LBP 2460 Service Manual - Page 168
Thermoswitch, Thermistor, <Note on reassembly>
 |
View all Canon LBP 2460 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 168 highlights
CHAPTER 3 b. Thermoswitch 1) Remove the wire cover. 2) Remove the 4 screws and then the lead wire and the thermoswitch. Πc. Thermistor 1) Remove the wire cover. 2) Disconnect the connector and remove the cable from the fixing left cover. ΠScrews Thermoswitch Figure 3-6-7 3 - 26 ΠΠConnector Figure 3-6-8 3) Remove the screw and the thermistor. ΠΠScrew Thermistor Figure 3-6-9 When installing the thermistor, ensure that its detection surface is uniformly contacting the fixing upper roller surface. If it is not making an uniform contact, check that the plate spring has not deformed.
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163 -
164 -
165 -
166 -
167 -
168 -
169 -
170 -
171 -
172 -
173 -
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
-
304
-
305
-
306
-
307
-
308
-
309
-
310
-
311
-
312
-
313
-
314
 |
 |
b.
Thermoswitch
1)
Remove the wire cover.
2)
Remove the 4 screws and then the lead
wire and the thermoswitch.
Screws
Thermoswitch
Figure 3-6-7
c.
Thermistor
1)
Remove the wire cover.
2)
Disconnect the connector and remove
the cable from the fixing left cover.
Connector
Figure 3-6-8
3)
Remove the screw and the thermistor.
Screw
Thermistor
Figure 3-6-9
<Note on reassembly>
When installing the thermistor, ensure that
its detection surface is uniformly contacting
the fixing upper roller surface.
If it is not making an uniform contact, check
that the plate spring has not deformed.
CHAPTER 3
3 - 26