Canon LBP 2460 Service Manual - Page 184
Remove the rear, front, lower and upper, out the envelope feeder driver PCB.
 |
View all Canon LBP 2460 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 184 highlights
CHAPTER 3 5) Remove the screw and take out the pickup motor. 4. Removal of the Envelope Feeder Driver PCB 1) Remove the rear, front, lower and upper covers. 2) Remove the envelope guides. 3) Remove the 2 connectors and the screw. ΠΠΠScrew Pick-up motor Figure 3-8-11 Note: After fastening the guides to the rack, attach the gear by spreading the guides apart. ΠConnectors Screw Figure 3-8-12 4) After removing the sensor lever, take out the envelope feeder driver PCB. 3 - 42 ΠΠSensor lever Envelope feeder driver PCB Figure 3-8-13
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179 -
180 -
181 -
182 -
183 -
184 -
185 -
186 -
187 -
188 -
189 -
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
-
304
-
305
-
306
-
307
-
308
-
309
-
310
-
311
-
312
-
313
-
314
 |
 |
5)
Remove the screw and take out the pick-
up motor.
Screw
Pick-up motor
Figure 3-8-11
Note:
After fastening the guides to the
rack,
attach the gear by spreading
the guides apart.
4. Removal of the Envelope Feeder
Driver PCB
1)
Remove the rear, front, lower and upper
covers.
2)
Remove the envelope guides.
3)
Remove the 2 connectors and the screw.
Connectors
Screw
Figure 3-8-12
4)
After removing the sensor lever, take
out the envelope feeder driver PCB.
Sensor lever
Envelope feeder driver PCB
Figure 3-8-13
CHAPTER 3
3 - 42