Canon LBP 2460 Service Manual - Page 27

Figure 1-5-1

C.

Unpacking and Installation

Condensation will form on metal surfaces when brought into a warm room from the cold.

Therefore, when moving the printer to a warm environment, leave it packed in its box for at least

an hour to acclimatize to room temperature.

1.

Printer

1)

Open the printer packaging.

2)

Take out the accessories. Confirm that the power cord, cartridge, and face-up tray are

included.

3)

The printer weighs approx. 48kg, therefore 4 people may be needed to lift the printer and to

move to the installation area.

4)

Take the plastic bag off the printer and peel the tape off each part. Check that none of the

covers were scratched or deformed during shipment.

5)

Open the delivery cover, and remove the pressure release spacer from the fixing unit.

6)

Open the upper cover, and remove the tape and the packing materials from inside the printer.

7)

Pull the two cassettes out of the printer and remove the packaging from the cassette.

2.

Cartridge

1)

Open the bag holding the cartridge and take out the cartridge.

2)

Remove the tape and the black sheet from the printer.

3)

Hold the cartridge on each side as shown in figure 1-5-7 and slowly rock it 5 to 6 times to

evenly distribute the toner.

4)

Place the cartridge on a flat surface. While holding down on the top of the cartridge with one

hand, grasp the tab with the other and gently pull out the cylinder tape.

5)

Open the upper cover of the printer, and load the cartridge with both hands. Slowly insert it

until it firmly contacts with the back of the slot.

3.

Envelope feeder

1)

Open the envelope feeder packaging.

2)

Take off the plastic bag and peel the tape off.

Check that none of the covers have been scratched or deformed during shipment.

3)

Remove the packing from the envelope feeder.

4)

Open the multi-purpose tray and remove the envelope feeder slot cover.

5)

Holding the envelope feeder in both hands, install it into the printer.

CHAPTER 1

1 - 15

1337

2300

900

100

100

834

857

*When paper deck is installed to printer.

Required space surrounding the printer with the

paper deck installed (option)

1086 (1150*)

(Unit: mm)

Section	Page
PREFACE	5
CONTENTS	7
CHAPTER 1	11
I. FEATURES	13
II. SPECIFICATIONS	15
III. SAFETY INFORMATION	19
IV. PARTS OF THE PRINTER	20
V. INSTALLATION	26
VI. MAINTENANCE AND SERVICING BY THE CUSTOMER	35
VII. OPERATION	37
CHAPTER 2	45
I. BASIC OPERATION	47
II. ENGINE CONTROL SYSTEM	50
III. LASER/SCANNER SYSTEM	72
IV. IMAGE FORMATION SYSTEM	78
V. PICK-UP/FEED SYSTEM	88
VI. OVERALL CONTROL SYSTEM	106
VII. OPTION CONTROL SYSTEM	110
VIII. ENVELOPE FEEDER	113
IX. DUPLEXING UNIT	117
X. PAPER DECK	127
CHAPTER 3	141
I. EXTERNALS	143
II. DRIVE SYSTEM	152
III. PAPER TRANSPORT SYSTEM	154
IV. EXPOSURE SYSTEM	163
V. ELECTROSTATIC IMAGING/DEVELOPING/CLEANING SYSTEM	164
VI. FIXING SYSTEM	166
VII. ELECTRONIC COMPONENTS	174
VIII. ENVELOPE FEEDER	181
IX. DUPLEXING UNIT	187
X. OPTION CONTROLLER	194
XI. PAPERDECK	195
CHAPTER 4	213
I. MAINTENANCE AND SERVICING	215
II. TOOLS	219
III. MEASUREMENT AND ADJUSTMENT	228
IV. INITIAL CHECK	232
V. IMAGE DEFECTS	233
VI. MALFUNCTION TROUBLESHOOTING	242
VII. PAPER FEEDING TROUBLESHOOTING	265
VIII. LOCATION OF ELECTRICAL PARTS/FUNCTION	272
IX.VARIABLE RESISTORS, LEDS, TEST PINS, JUMPERS, AND SWITCHES ON PC BOARDS	287
X. LIST OF LUBRICANTS, CLEANERS	296
APPENDIX	297
I. GENERAL TIMING CHART-1/2	299
GENERAL TIMING CHART-2/2	300
II. GENERAL CIRCUIT DIAGRAM-1/3	301
GENERAL CIRCUIT DIAGRAM-2/3	302
GENERAL CIRCUIT DIAGRAM-3/3	303

Canon LBP 2460 Service Manual - Page 27

Unpacking and Installation, Printer, Cartridge, Envelope feeder - toner cartridges

Page 27 highlights