Dell PowerEdge R805 Hardware Owner's Manual (PDF) - Page 37

Gate A20 failure, The DIMM group for CPU

Get Dell PowerEdge R805 PDF manuals and user guides View all Dell PowerEdge R805 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Table 1-7. System Messages (continued) Message Causes Corrective Actions Error: Incorrect memory configuration CPU n The DIMM group for CPU n See "General Memory is incorrectly configured and Module Installation caused the system to halt. Guidelines" on page 114 for memory configuration information. If the problem persists, see "Troubleshooting System Memory" on page 150. !!*** Error: Remote Access Controller initialization failure *** RAC virtual USB devices may not be available... Remote Access Controller initialization failure Ensure that the Remote Access Controller is properly installed. See "Installing a RAC Card" on page 106. Gate A20 failure Faulty keyboard controller; See "Getting Help" on faulty system board. page 175. General failure The operating system is unable to carry out the command. This message is usually followed by specific information. Note the information, and take the appropriate action to resolve the problem. HyperTransport error caused a system reset! Please check the system event log for details! A fatal system error occurred Check the SEL for and caused the system to information that was logged reboot. during the error. See the applicable troubleshooting section in "Troubleshooting Your System" on page 137 for any faulty components specified in the SEL. Invalid NVRAM configuration, Resource Reallocated System detected and No action is required. corrected a resource conflict. About Your System 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
About Your System
37
Error: Incorrect
memory
configuration
CPU
n
The DIMM group for CPU
n
is incorrectly configured and
caused the system to halt.
See "General Memory
Module Installation
Guidelines" on page 114 for
memory configuration
information. If the problem
persists, see
"Troubleshooting System
Memory" on page 150.
!!*** Error:
Remote Access
Controller
initialization
failure *** RAC
virtual USB
devices may not
be available...
Remote Access Controller
initialization failure
Ensure that the Remote
Access Controller is properly
installed. See "Installing a
RAC Card" on page 106.
Gate A20 failure
Faulty keyboard controller;
faulty system board.
See "Getting Help" on
page 175.
General failure
The operating system is
unable to carry out the
command.
This message is usually
followed by specific
information. Note the
information, and take the
appropriate action to resolve
the problem.
HyperTransport
error caused a
system reset!
Please check the
system event log
for details!
A fatal system error occurred
and caused the system to
reboot.
Check the SEL for
information that was logged
during the error. See the
applicable troubleshooting
section in "Troubleshooting
Your System" on page 137 for
any faulty components
specified in the SEL.
Invalid NVRAM
configuration,
Resource Re-
allocated
System detected and
corrected a resource conflict.
No action is required.
Table 1-7.
System Messages
(continued)
Message
Causes
Corrective Actions