Dell PowerEdge R805 Hardware Owner's Manual (PDF) - Page 41

Plug & Play, Installing a RAC Card

Get Dell PowerEdge R805 PDF manuals and user guides View all Dell PowerEdge R805 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Table 1-7. System Messages (continued) Message Causes Corrective Actions PCIe Training Error: Slot n Faulty or improperly installed Reseat the PCIe card in the PCIe card in the specified specified slot number. See slot. "Expansion Cards" on page 91. If the problem persists, see "Getting Help" on page 175. Plug & Play Configuration Error Error encountered in initializing PCIe device; faulty system board. Install the NVRAM_CLR jumper and reboot the system. See Figure 6-1 for jumper location. If the problem persists, see "Troubleshooting Expansion Cards" on page 158. Read fault Requested sector not found The operating system cannot Replace the USB medium or read from the hard drive or device. Ensure that the USB USB device, the system could or hard drive cables are not find a particular sector on properly connected. See the disk, or the requested "Troubleshooting a USB sector is defective. Device" on page 143, or "Troubleshooting a Hard Drive" on page 155 for the appropriate drive(s) installed in your system. Remote Access RAC cables not connected, Controller cable or RAC card installed in error or wrong expansion slot. incorrect card in the RAC slot. Check that the RAC cables are connected, and that the RAC card is installed in the correct expansion slot. See "Installing a RAC Card" on page 106. Remote configuration update attempt failed System unable to process Remote Configuration request Retry Remote Configuration. About Your System 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
About Your System
41
PCIe Training
Error: Slot
n
Faulty or improperly installed
PCIe card in the specified
slot.
Reseat the PCIe card in the
specified slot number. See
"Expansion Cards" on
page 91. If the problem
persists, see "Getting Help"
on page 175.
Plug & Play
Configuration
Error
Error encountered in
initializing PCIe device;
faulty system board.
Install the NVRAM_CLR
jumper and reboot the
system. See Figure 6-1 for
jumper location. If the
problem persists, see
"Troubleshooting Expansion
Cards" on page 158.
Read fault
Requested sector
not found
The operating system cannot
read from the hard drive or
USB device, the system could
not find a particular sector on
the disk, or the requested
sector is defective.
Replace the USB medium or
device. Ensure that the USB
or hard drive cables are
properly connected. See
"Troubleshooting a USB
Device" on page 143, or
"Troubleshooting a Hard
Drive" on page 155 for the
appropriate drive(s) installed
in your system.
Remote Access
Controller cable
error or
incorrect card in
the RAC slot.
RAC cables not connected,
or RAC card installed in
wrong expansion slot.
Check that the RAC cables
are connected, and that the
RAC card is installed in the
correct expansion slot. See
"Installing a RAC Card" on
page 106.
Remote
configuration
update attempt
failed
System unable to process
Remote Configuration
request
Retry Remote Configuration.
Table 1-7.
System Messages
(continued)
Message
Causes
Corrective Actions