Dell S2810dn Dell Smart Printer Users Guide - Page 130

IP Filter IPv4, Login Name: Device

Page 130 highlights

Re-enter Pre-Shared Key Enters the shared key again to confirm it. IKE SA Lifetime Sets the lifetime for IKE SA from 5 to 28,800 minutes. IPsec SA Lifetime Sets the lifetime for IPsec SA from 5 to 2,880 minutes. DH Group Sets the DH group. PFS Select the check box to enable the PFS setting. Remote peers IPv4 address Sets the IP address to connect to. Remote peers IPv6 address Sets the IP address to connect to. Non IPsec communication Allows communication with a device which does not support IPsec. policy NOTE: If IPsec is enabled with incorrect settings, you must disable it using the IPsec menu on the operator panel. 802.1x Purpose: To specify the settings for IEEE 802.1x authentication for encrypted communication to the printer. Values: Configure 802.1x Enable IEEE 802.1x Select the check box to enable IEEE 802.1x authentication. Authentication Method EAP-MD5 Selects the authentication method to use for IEEE 802.1x authentication. EAP-MSCHAPv2 PEAP/MSCHAPv2 Login Name: (Device Sets the login name (device name) for IEEE 802.1x authentication using Name) up to 128 alphanumeric characters. Password Sets the login password for IEEE 802.1x authentication using up to 128 alphanumeric characters. Re-enter Password Confirms the set login password. IP Filter (IPv4) Purpose: To specify the IP address and subnet mask to be permitted or denied access to the printer. Values: Access List Address Address Mask Active Mode Sets the IP addresses that are permitted or denied access to the printer. Enter a numeric value between 0 and 255 in each field. Sets the subnet mask that are permitted or denied access to the printer. Enter a numeric value between 0 and 255 in each field. Reject Rejects printing from specified network address. Accept Permits printing from specified network address. Off Disables the IP Filter feature for the specified IP address. To configure the IP Filter feature, enter an IP address to be filtered in the Address field and the subnet mask in the Address Mask field. Enter a numeric value between 0 and 255 in each field. "*" is appended to the current value. 130 Dell™ Printer Configuration Web Tool

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
  • 287
  • 288
  • 289
  • 290
  • 291
  • 292
  • 293
  • 294
  • 295
  • 296
  • 297
  • 298
  • 299
  • 300
  • 301
  • 302
  • 303
  • 304
  • 305
  • 306
  • 307
  • 308
  • 309
  • 310
  • 311
  • 312
  • 313
  • 314
  • 315
  • 316

130
Dellâ„¢ Printer Configuration Web Tool
NOTE:
If IPsec is enabled with incorrect settings, you must disable it using the
IPsec
menu on the operator panel.
802.1x
Purpose:
To specify the settings for IEEE 802.1x authentication for encrypted communication to the printer.
Values:
IP Filter (IPv4)
Purpose:
To specify the IP address and subnet mask to be permitted or denied access to the printer.
Values:
To configure the IP Filter feature, enter an IP address to be filtered in the Address field and the subnet mask in the
Address Mask field. Enter a numeric value between 0 and 255 in each field. "*" is appended to the current value.
Re-enter Pre-Shared Key
Enters the shared key again to confirm it.
IKE SA Lifetime
Sets the lifetime for IKE SA from 5 to 28,800 minutes.
IPsec SA Lifetime
Sets the lifetime for IPsec SA from 5 to 2,880 minutes.
DH Group
Sets the DH group.
PFS
Select the check box to enable the PFS setting.
Remote peers IPv4 address
Sets the IP address to connect to.
Remote peers IPv6 address
Sets the IP address to connect to.
Non IPsec communication
policy
Allows communication with a device which does not support IPsec.
Configure 802.1x
Enable IEEE 802.1x
Select the check box to enable IEEE 802.1x authentication.
Authentication Method
EAP-MD5
Selects the authentication method to use for IEEE
802.1x authentication.
EAP-MS-
CHAPv2
PEAP/MS-
CHAPv2
Login Name: (Device
Name)
Sets the login name (device name) for IEEE 802.1x authentication using
up to 128 alphanumeric characters.
Password
Sets the login password for IEEE 802.1x authentication using up to 128
alphanumeric characters.
Re-enter Password
Confirms the set login password.
Access List
Address
Sets the IP addresses that are permitted or denied access to the printer. Enter a
numeric value between 0 and 255 in each field.
Address Mask
Sets the subnet mask that are permitted or denied access to the printer. Enter a
numeric value between 0 and 255 in each field.
Active Mode
Reject
Rejects printing from specified network address.
Accept
Permits printing from specified network address.
Off
Disables the IP Filter feature for the specified IP address.