HP 500X HP JetDirect Print Servers 600N/400N/500X/300X Administrator's Guide - - Page 121

Table 7.4, DLC/LLC Configuration Messages, General HP JetDirect Messages 1 of 15 - jetdirect printer installer download

Page 121 highlights

Table 7.4 DLC/LLC Configuration Messages Message DLC/LLC STATUS: SERVER ADDRESS: Description Current DLC/LLC status: DISABLED: Indicates that DLC/LLC was manually disabled through the printer's control panel (if available). DISABLED: Indicates that LAN Server was manually disabled through the printer's control panel (if available). READY: Indicates the HP JetDirect print server is awaiting data. NOT IN USE: Code is in the middle of a download. Station address of the remote end of the connection. Table 7.5 General HP JetDirect Messages (1 of 15) Message ARP DUPLICATE IP ADDRESS AUTONEGOTIATION ON OFF AUTO-REMOVAL ERROR BABBLE ERROR BAD BOOTP REPLY Description The ARP layer has detected another node on the network using the same IP address as the HP JetDirect print server. Extended error information below this message shows the hardware address of the other node. Identifies whether IEEE 802.3 Autonegotiation on the HP JetDirect 10/100TX port is enabled (ON) or disabled (OFF). If ON, the HP JetDirect print server will attempt to automatically configure itself onto the network at the proper speed (10 or 100 Mbps) and mode (half or full duplex). If OFF, you must manually configure the speed and mode using switches or jumpers on the print server. The HP JetDirect print server detected an internal hardware error following the Token Ring beacon auto-removal process and has removed itself from the ring. Run the power-on self-test: turn the printer off, then on again. If the error persists, replace the HP JetDirect print server. For information on replacing your HP JetDirect print server, see the hardware installation guide for your print server. An error was detected in the BOOTP reply that the HP JetDirect print server received. The BOOTP reply either had insufficient data in the UDP datagram to contain the minimum BOOTP header of 236 bytes, had an operation field that was not BOOTPREPLY(0X02), had a header field that did not match the print servers hardware address, or had a UDP source port that was not the BOOTP server port (67/udp). EN HP JetDirect Configuration Page Messages 115

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164

EN
HP JetDirect Configuration Page Messages 115
Table 7.4
DLC/LLC Configuration Messages
Message
Description
DLC/LLC STATUS:
Current DLC/LLC status:
DISABLED: Indicates that DLC/LLC was manually disabled
through the printer's control panel (if available).
DISABLED: Indicates that LAN Server was manually
disabled through the printer's control panel (if available).
READY: Indicates the HP JetDirect print server is awaiting
data.
NOT IN USE: Code is in the middle of a download.
SERVER ADDRESS:
Station address of the remote end of the connection.
Table 7.5
General HP JetDirect Messages (1 of 15)
Message
Description
ARP DUPLICATE IP
ADDRESS
The ARP layer has detected another node on the network
using the same IP address as the HP JetDirect print server.
Extended error information below this message shows the
hardware address of the other node.
AUTONEGOTIATION
ON
OFF
Identifies whether IEEE 802.3 Autonegotiation on the
HP JetDirect 10/100TX port is enabled (ON) or disabled
(OFF). If ON, the HP JetDirect print server will attempt to
automatically configure itself onto the network at the proper
speed (10 or 100 Mbps) and mode (half or full duplex). If
OFF, you must manually configure the speed and mode
using switches or jumpers on the print server.
AUTO-REMOVAL
ERROR
The HP
JetDirect print server detected an internal hardware
error following the Token Ring beacon auto-removal process
and has removed itself from the ring.
BABBLE ERROR
Run the power-on self-test: turn the printer off, then on
again. If the error persists, replace the HP JetDirect print
server. For information on replacing your HP JetDirect print
server, see the hardware installation guide for your print
server.
BAD BOOTP REPLY
An error was detected in the BOOTP reply that the
HP
JetDirect print server received. The BOOTP reply either
had insufficient data in the UDP datagram to contain the
minimum BOOTP header of 236 bytes, had an operation
field that was not BOOTPREPLY(0X02), had a header field
that did not match the print servers hardware address, or
had a UDP source port that was not the BOOTP server port
(67/udp).