HP 500X HP JetDirect Print Servers 600N/400N/500X/300X Administrator's Guide - - Page 52

enabled. You can disable password protection by typing, when prompted for a new password - jetdirect reset default

Get HP 500X - JetDirect Print Server PDF manuals and user guides
UPC - 088698574287
View all HP 500X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

To set configuration parameters, you must set up a Telnet connection from your system to the HP JetDirect print server. 1. Type the following at the system prompt: telnet where may be the assigned address from BOOTP, RARP, DHCP, the printer control panel, or the default IP address. The default IP address is 192.0.0.192. The is listed on the JetDirect configuration page. 2. When the server responds connected to IP address, press [Enter] twice to make sure that the Telnet connection is initialized. 3. If you are prompted for a password, type the correct password. By default, Telnet does not require a password, but you can set up to a 14-character password by using the password command (passwd). Once a password is set, password protection is enabled. You can disable password protection by typing 0 (zero) when prompted for a new password, or by performing a cold reset on the print server. Note Any time during the Telnet session you can type:? then press [Enter] to view available configuration parameters, the correct command format, and a list of additional commands to display. To print current configuration information, type / then press [Enter]. 46 TCP/IP Configuration EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
46 TCP/IP Configuration
EN
To set configuration parameters, you must set up a Telnet
connection from your system to the HP JetDirect print server.
1.
Type the following at the system prompt:
telnet <IP address>
where
<IP address>
may be the assigned address from
BOOTP, RARP, DHCP, the printer control panel, or the default
IP address. The default IP address is 192.0.0.192. The
<IP address>
is listed on the JetDirect configuration page.
2.
When the server responds
connected to IP address
, press
[Enter]
twice to make sure that the Telnet connection is
initialized.
3.
If you are prompted for a password, type the correct password.
By default, Telnet does not require a password, but you can set
up to a 14-character password by using the password command
(passwd). Once a password is set, password protection is
enabled. You can disable password protection by typing
0
(zero)
when prompted for a new password, or by performing a cold
reset on the print server.
Note
Any time during the Telnet session you can type:
?
then press
[Enter]
to view available configuration
parameters, the correct command format, and a list
of additional commands to display. To print current
configuration information, type
/
then press
[Enter]
.