HP 500X HP JetDirect Print Servers 600N/400N/500X/300X Administrator's Guide - - Page 123

HP JetDirect Configuration Messages 117, Table 7.5, General HP JetDirect Messages 3 of 15 - reset jetdirect print server

Page 123 highlights

Table 7.5 General HP JetDirect Messages (3 of 15) Message Description DATA RATE: 4 Mbps 16 Mbps JUMPER ERROR The Token Ring data rate at which the HP JetDirect print server can transfer information. This setting should be either 4 or 16 Megabits per second (4 or 16 Mbps), depending on your network configuration. If the DATA RATE field displays JUMPER ERROR (older HP JetDirect print servers), check the jumper switch setting on the HP JetDirect print server. For information on setting the jumper switch on the print server, see the hardware installation guide for your print server. DATE MANUFACTURED Identifies the date of manufacture of the HP JetDirect print server. DHCP NACK After several attempts, the DHCP server has failed to acknowledge the configuration. The JetDirect print server will restart the configuration process. DISCONNECTED The Novell NetWare protocol is disconnected. Check the server and the print server. DISCONNECTING FROM SERVER The server has been shut down because of a configuration change or reset request. This message automatically clears after a few seconds, unless the printer is offline, is in an error state, or is servicing another I/O port or another network protocol. DISCONNECTING SPX TIMEOUT The SPX connection to the print server was lost after the connection had been made. This indicates a possible network problem, or a problem with the print server. Make sure all cables and routers are functioning correctly. Try restarting the print server. DUP NODE ADDRESS The HP JetDirect print server found another station on the ring that already has the address which the HP JetDirect print server wishes to use. Make sure that all addresses are unique. ERR NEGOTIATING BUFFER SIZE A failure was detected when selecting the buffer size to be used when reading print data from the file server. This may indicate a network problem. FAIL RESERVING PRINTER NUM When the HP JetDirect print server is configured for multiple file servers, the error is only displayed on the configuration page if none of the file servers was successfully connected. The SPX connection to the print server was lost when the HP JetDirect print server attempted to reserve the printer number. This indicates a possible network problem, or a problem with the print server. Make sure all cables and routers are functioning correctly. Try restarting the print server. EN HP JetDirect Configuration Page Messages 117

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164

EN
HP JetDirect Configuration Page Messages 117
DATA RATE:
4 Mbps
16 Mbps
JUMPER ERROR
The Token Ring data rate at which the HP JetDirect print
server can transfer information. This setting should be either
4 or 16 Megabits per second (4 or 16 Mbps), depending on
your network configuration. If the DATA RATE field displays
JUMPER ERROR (older HP JetDirect print servers), check
the jumper switch setting on the HP JetDirect print server.
For information on setting the jumper switch on the print
server, see the hardware installation guide for your print
server.
DATE
MANUFACTURED
Identifies the date of manufacture of the HP JetDirect print
server.
DHCP NACK
After several attempts, the DHCP server has failed to
acknowledge the configuration. The JetDirect print server
will restart the configuration process.
DISCONNECTED
The Novell NetWare protocol is disconnected. Check the
server and the print server.
DISCONNECTING
FROM SERVER
The server has been shut down because of a configuration
change or reset request. This message automatically clears
after a few seconds, unless the printer is offline, is in an error
state, or is servicing another I/O port or another network
protocol.
DISCONNECTING -
SPX TIMEOUT
The SPX connection to the print server was lost after the
connection had been made. This indicates a possible
network problem, or a problem with the print server. Make
sure all cables and routers are functioning correctly. Try
restarting the print server.
DUP NODE ADDRESS
The HP JetDirect print server found another station on the
ring that already has the address which the HP JetDirect
print server wishes to use. Make sure that all addresses are
unique.
ERR NEGOTIATING
BUFFER SIZE
A failure was detected when selecting the buffer size to be
used when reading print data from the file server. This may
indicate a network problem.
When the HP
JetDirect print server is configured for multiple
file servers, the error is only displayed on the configuration
page if none of the file servers was successfully connected.
FAIL RESERVING
PRINTER NUM
The SPX connection to the print server was lost when the
HP JetDirect print server attempted to reserve the printer
number. This indicates a possible network problem, or a
problem with the print server. Make sure all cables and
routers are functioning correctly. Try restarting the print
server.
Table 7.5
General HP JetDirect Messages (3 of 15)
Message
Description