HP 500X HP JetDirect Print Servers 600N/400N/500X/300X Administrator's Guide - - Page 58

Using the Printer Control Panel

Get HP 500X - JetDirect Print Server PDF manuals and user guides
UPC - 088698574287
View all HP 500X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Using the Printer Control Panel This subsection describes how to configure the HP JetDirect internal print server using the printer's control panel. If configuration of the HP JetDirect print server is supported from your printer control panel, you can set the network configuration parameters listed below. q IP address of the print server q Subnet mask q Default gateway address q Syslog server address q Idle timeout period If the printer control panel configuration is supported, see the hardware installation guide for your print server or the user guide for your printer for instructions on how to configure the print server from the printer control panel. If you need to configure other parameters, use BOOTP/TFTP to configure all the parameters for the print server. If the HP JetDirect print server is configured to receive its configuration from the printer control panel, the configuration is saved on the print server over power cycles. For information on these parameters see Table 3.4. 52 TCP/IP Configuration EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
52 TCP/IP Configuration
EN
Using the Printer Control Panel
This subsection describes how to configure the HP JetDirect
internal print server using the printer's control panel.
If configuration of the HP JetDirect print server is supported from
your printer control panel, you can set the network configuration
parameters listed below.
●
IP address of the print server
●
Subnet mask
●
Default gateway address
●
Syslog server address
●
Idle timeout period
If the printer control panel configuration is supported, see the
hardware installation guide for your print server or the user guide
for your printer for instructions on how to configure the print server
from the printer control panel.
If you need to configure other parameters, use BOOTP/TFTP to
configure all the parameters for the print server.
If the HP JetDirect print server is configured to receive its
configuration from the printer control panel, the configuration is
saved on the print server over power cycles. For information on
these parameters see Table 3.4.