HP ET115AV HP xw4400 Workstation - Service and Technical Reference Guide - Page 103

Installing hard drives in the optical drive bays (optional),

Get HP ET115AV PDF manuals and user guides View all HP ET115AV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 103 highlights

5. Connect the data cable from the hard drive (1) to the serial ATA port (2). SATA0 port is shown in the following illustration. ● Connect SATA 0 to SATA0. ● Connect SATA 1 to SATA1. Figure 4-50 Connecting the SATA cable to the hard drive To install three to four SATA hard drives: 1. Follow the instructions for installing two SATA hard drives above. 2. Follow the instructions for installing the hard drive into the optical drive slot. NOTE: If installing three SATA hard drives, you must install hard drives in at least one optical drive bay. If installing four SATA hard drives, you must install hard drives in at least two optical drive bays. 3. Connect the data and power cable to the drives. ● Connect SATA 2 to SATA2. ● Connect SATA 3 to SATA3. Installing hard drives in the optical drive bays (optional) 1. Disconnect power from the system (Predisassembly procedures on page 57), remove the side access panel (Side access panel on page 62), and the front bezel (Front Bezel on page 63). ENWW Steps for removal and replacement of components 93

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
5.
Connect the data cable from the hard drive
(1)
to the serial ATA port
(2)
. SATA0 port is shown in
the following illustration.
●
Connect SATA 0 to SATA0.
●
Connect SATA 1 to SATA1.
Figure 4-50
Connecting the SATA cable to the hard drive
To install three to four SATA hard drives:
1.
Follow the instructions for installing two SATA hard drives above.
2.
Follow the instructions for installing the hard drive into the optical drive slot.
NOTE:
If installing three SATA hard drives, you must install hard drives in at least one optical
drive bay. If installing four SATA hard drives, you must install hard drives in at least two optical
drive bays.
3.
Connect the data and power cable to the drives.
●
Connect SATA 2 to SATA2.
●
Connect SATA 3 to SATA3.
Installing hard drives in the optical drive bays (optional)
1.
Disconnect power from the system (
Predisassembly procedures
on page
57
), remove the side
access panel (
Side access panel
on page
62
), and the front bezel (
Front Bezel
on page
63
).
ENWW
Steps for removal and replacement of components
93