HP ET115AV HP xw4400 Workstation - Service and Technical Reference Guide - Page 80

Memory, CAUTION

Get HP ET115AV PDF manuals and user guides View all HP ET115AV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

3. Remove the four screws (2) from the rear of the chassis with a Phillips screwdriver, and lift it (3) out of the chassis. Figure 4-16 Removing the system fan To replace the system fan assembly, reverse the previous steps. CAUTION: When replacing the system fan, be sure that the fan is situated so that the airflow direction arrow is pointing toward the rear of the chassis. Memory To remove a memory module: 1. Disconnect power from the system (Predisassembly procedures on page 57) and remove the side access panel (Side access panel on page 62). CAUTION: To ensure that memory modules are not damaged during removal or installation, power off the workstation and unplug the power cord from the AC power outlet. Wait until the LED on the back of the power supply turns off before removing memory. If you do not unplug the power cord while installing memory, your memory modules might be damaged and the system will not recognize the memory changes. 2. Gently push outwards on the socket levers (1). 70 Chapter 4 Removal and replacement procedures ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
3.
Remove the four screws
(2)
from the rear of the chassis with a Phillips screwdriver, and lift it
(3)
out of the chassis.
Figure 4-16
Removing the system fan
To replace the system fan assembly, reverse the previous steps.
CAUTION:
When replacing the system fan, be sure that the fan is situated so that the airflow direction
arrow is pointing toward the rear of the chassis.
Memory
To remove a memory module:
1.
Disconnect power from the system (
Predisassembly procedures
on page
57
) and remove the side
access panel (
Side access panel
on page
62
).
CAUTION:
To ensure that memory modules are not damaged during removal or installation,
power off the workstation and unplug the power cord from the AC power outlet. Wait until the LED
on the back of the power supply turns off before removing memory. If you do not unplug the power
cord while installing memory, your memory modules might be damaged and the system will not
recognize the memory changes.
2.
Gently push outwards on the socket levers
(1)
.
70
Chapter 4
Removal and replacement procedures
ENWW