HP ET115AV HP xw4400 Workstation - Service and Technical Reference Guide - Page 94

CAUTION, Align the screws with the grooves in the drive bay and gently slide

Get HP ET115AV PDF manuals and user guides View all HP ET115AV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 94 highlights

4. After pulling the drive (1) out, remove the four guide screws (2) from the drive. Only remove the four guide screws if you plan to install another drive. Figure 4-34 Removing the optical drive screws To install an optical drive: 1. Disconnect power from the system (Predisassembly procedures on page 57), remove the side access panel (Side access panel on page 62) and remove the front bezel (Front Bezel on page 63). 2. Insert the four guide screws (1) into the drive. 3. Align the screws with the grooves in the drive bay and gently slide 2 the drive into the unit until it snaps into place. CAUTION: Ensure that the optical drive is secure by pulling to see if the drive can become easily disengaged. Failure to do so can cause damage to the drive when moving the workstation. 84 Chapter 4 Removal and replacement procedures ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
4.
After pulling the drive
(1)
out, remove the four guide screws
(2)
from the drive. Only remove the
four guide screws if you plan to install another drive.
Figure 4-34
Removing the optical drive screws
To install an optical drive:
1.
Disconnect power from the system (
Predisassembly procedures
on page
57
), remove the side
access panel (
Side access panel
on page
62
) and remove the front bezel (
Front Bezel
on page
63
).
2.
Insert the four guide screws
(1)
into the drive.
3.
Align the screws with the grooves in the drive bay and gently slide
2
the drive into the unit until it
snaps into place.
CAUTION:
Ensure that the optical drive is secure by pulling to see if the drive can become easily
disengaged. Failure to do so can cause damage to the drive when moving the workstation.
84
Chapter 4
Removal and replacement procedures
ENWW