HP ET115AV HP xw4400 Workstation - Service and Technical Reference Guide - Page 87

PCI, Lift the PCI card

Get HP ET115AV PDF manuals and user guides View all HP ET115AV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 87 highlights

5. Close the PCI retention clamp (4) by rotating the clamp downward and pushing on the two green snaps down from the rear panel of the chassis. Figure 4-24 Installing the PCI card PCI To remove a PCI card: 1. Disconnect power from the system (Predisassembly procedures on page 57), remove the side access panel (Side access panel on page 62), and remove the PCI retainer (PCI retainer on page 74), if installed. 2. Lift the PCI levers (1) by first pressing down and then up. 3. Lift the PCI card (2) out of the chassis. Store the card in an anti-static bag. 4. Install a PCI slot cover and close the PCI levers. If the PCI levers do not close, be sure all cards are properly seated and then try again. Figure 4-25 Removing the PCI card ENWW Steps for removal and replacement of components 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
5.
Close the PCI retention clamp
(4)
by rotating the clamp downward and pushing on the two green
snaps down from the rear panel of the chassis.
Figure 4-24
Installing the PCI card
PCI
To remove a PCI card:
1.
Disconnect power from the system (
Predisassembly procedures
on page
57
), remove the side
access panel (
Side access panel
on page
62
), and remove the PCI retainer (
PCI retainer
on page
74
), if installed.
2.
Lift the PCI levers
(1)
by first pressing down and then up.
3.
Lift the PCI card
(2)
out of the chassis. Store the card in an anti-static bag.
4.
Install a PCI slot cover and close the PCI levers. If the PCI levers do not close, be sure all cards
are properly seated and then try again.
Figure 4-25
Removing the PCI card
ENWW
Steps for removal and replacement of components
77