HP Vectra XU 6/XXX HP Vectra XU6/150 PC - User’s Guide - Page 56

Installing A Hard Disk Drive

Get HP Vectra XU 6/XXX PDF manuals and user guides View all HP Vectra XU 6/XXX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

two internal shelves for 3.5-inch hard disks two shelves for 3.5-inch disk drives three shelves for 5.25-inch disk drives INSTALLING A HARD DISK DRIVE The computer has an integrated SCSI controller and an integrated Enhanced IDE controller. • The Enhanced IDE controller supports up to four IDE devices: • two IDE devices can be connected to the Primary Channel cable (connected to the grey connector on the system board) • two IDE devices can be connected to the Secondary Channel cable (connected to the red connector on the system board) • The SCSI controller supports up to seven SCSI devices (up to five SCSI devices can be connected to the internal SCSI cable). Before Installing an IDE Hard Disk Refer to the drive's installation guide to see if you must set jumpers or if there is a special installation procedure to follow. Before Installing a SCSI Hard Disk If you are installing an additional SCSI drive you must select a SCSI address for the new drive. SCSI addresses range from 0 to 7, with SCSI address 0 used by the first SCSI drive and SCSI address 7 reserved for the integrated SCSI controller. NOTE You don't need to select a SCSI address for Plug and Play SCSI hard disks (SCSI hard disks which support the SCAM protocol).

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
two internal shelves
for 3.5-inch hard disks
two shelves for
3.5-inch disk drives
three shelves for
5.25-inch disk drives
INSTALLING A HARD DISK DRIVE
The computer has an integrated SCSI controller and an integrated Enhanced IDE controller.
•
The Enhanced IDE controller supports up to four IDE devices:
•
two IDE devices can be connected to the Primary Channel cable (connected to the
grey connector on the system board)
•
two IDE devices can be connected to the Secondary Channel cable (connected to the
red connector on the system board)
•
The SCSI controller supports up to seven SCSI devices
(up to five SCSI devices can be connected to the internal SCSI cable).
Before Installing an IDE Hard Disk
Refer to the drive’s installation guide to see if you must set jumpers or if there is a special
installation procedure to follow.
Before Installing a SCSI Hard Disk
If you are installing an additional SCSI drive you must select a SCSI address for the new drive.
SCSI addresses range from 0 to 7, with SCSI address 0 used by the first SCSI drive and SCSI
address 7 reserved for the integrated SCSI controller.
NOTE
You don’t need to select a SCSI address for Plug and
Play SCSI hard disks (SCSI hard disks which support
the SCAM protocol).