HP Workstation i2000 hp workstation i2000 owner's guide (a6037-90003) - Page 104

Which Pins To Jumper.

Get HP Workstation i2000 PDF manuals and user guides View all HP Workstation i2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 104 highlights

hp workstation i2000 owner's guide Which Pins To Jumper. First, determine which drive is installed in your system. Your drive will be type A, B or C. Then use the table for the proper pins to jumper on your drive. Using the jumpers provided, set the SCSI ID on the jumper block located on the bottom of the hard disk drive. Do not use the 12-pin jumper block next to the power connector. / NOTE Jumpers must be installed vertically. If jumpers are installed horizontally across adjacent pins, there is no effect. However, this is a good way to store unused jumpers. 104

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
hp workstation i2000 owner’s guide
104
Which Pins To Jumper.
First, determine which drive is installed in your system. Your drive will be type A, B or C. Then
use the table for the proper pins to jumper on your drive.
Using the jumpers provided, set the SCSI ID on the jumper block located on the bottom of the
hard disk drive. Do
not
use the 12-pin jumper block next to the power connector.
/
NOTE
Jumpers must be installed vertically. If jumpers are installed horizontally across adjacent pins,
there is no effect. However, this is a good way to store unused jumpers.