HP Workstation i2000 hp workstation i2000 owner's guide (a6037-90003) - Page 93

Installation of Upgrade Components

Get HP Workstation i2000 PDF manuals and user guides View all HP Workstation i2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 93 highlights

hp workstation i2000 owner's guide 8. Installation of Upgrade Components 8.1 Verification of the Jumper Settings The following section describes the jumper settings on the boards in the i2000 system. The Processor Present jumper (J1) on the processor board (refer to Table 20) configures the ITP scan chain for single or dual processor mode. The jumper should be configured to match the number of processors in the system, but is on necessary for functional performance. 8.1.1 Processor Jumpers Table 20. Processor Present (J1) Single Processor Scan Chain Present (valid) 1-2* Not Present (invalid) 2-3 Dual Processor Scan Chain Present 4-5 Not Present 5-6* DEFAULT* Processor Present (J1) 93

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
hp workstation i2000 owner’s guide
93
8.
Installation of Upgrade Components
8.1
Verification of the Jumper Settings
The following section describes the jumper settings on the boards in the i2000 system.
The Processor Present jumper (J1) on the processor board (refer to Table 20)
configures the ITP scan chain for single or dual processor mode.
The jumper should be
configured to match the number of processors in the system, but is on necessary for
functional performance.
8.1.1
Processor Jumpers
Table 20. Processor Present (J1)
Single Processor Scan Chain
Present (valid)
1-2*
Not Present (invalid)
2-3
Dual Processor Scan Chain
Present
4-5
Not Present
5-6*
DEFAULT*
Processor
Present (J1)