IBM 4500R Hardware Maintenance Manual - Page 28

The Multiple Link Interface Driver MLID cannot be registered with the, Link Support Layer LSL.

Get IBM 4500R - Netfinity - 8656 PDF manuals and user guides
UPC - 087944567837
View all IBM 4500R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Table 2. Novell NetWare or IntraNetWare ODI driver messages for the Ethernet controller. PCNTNW-NW-054 The adapter did not respond to the initialization command. Explanation: The adapter did not respond when the driver tried to initialize it. Action: Verify that the Ethernet controller is enabled. If the Ethernet controller is enabled, go to "Starting the diagnostic programs" on page 14 to run the diagnostic programs. PCNTNW-NW-058 The adapter did not respond to the initialization command. Explanation: The interrupt request (IRQ) setting might not be valid or the EEPROM information might be incorrect. Action: Make sure the IRQ settings are correct in the Configuration/Setup Utility program. for information on setting the interrupt requests. If the IRQ settings are correct, go to "Starting the diagnostic programs" on page 14 to run the diagnostic programs. PCNTNW-NW-066 The cable might be disconnected from the adapter. Explanation: The cable might be disconnected from the server Ethernet port. Action: Verify that a cable is connected to the Ethernet port. PCNTNW-NW-071 The matching virtual adapter could not be found. Explanation: You tried to load another instance of the driver with a different I/O address. This new adapter could not be found. Action: Verify that you installed an IBM Netfinity 10/100 Fault Tolerant Adapter and make sure that the adapter is seated correctly. If the adapter is seated correctly, go to "Starting the diagnostic programs" on page 14 to run the diagnostic programs.. PCNTNW-NW-072 A resource tag is unavailable. Explanation: The driver tried to allocate some resources that were not available. Action: Add more memory, or free some memory resources in the server. Then, restart the server. PCNTNW-NW-073 Unable to allocate memory Explanation: The driver failed to allocate the memory needed for normal operation. Action: Add more memory, or free some memory resources in the server. Then, restart the server. PCNTNW-NW-074 The hardware interrupt cannot be set. Explanation: An attempt was made to initialize a given hardware interrupt. The attempt was not successful. Action: Verify that the Ethernet controller is enabled. If the Ethernet controller is enabled, go to "Starting the diagnostic programs" on page 14 to run the diagnostic programs. If you have an Ethernet adapter installed, make sure that the adapter does not share an IRQ with any other device. PCNTNW-NW-075 The Multiple Link Interface Driver (MLID) cannot be registered with the Link Support Layer (LSL). Explanation: An error occurred while the driver was trying to register with the LSL. Action: Check the version of the NetWare or IntraNetWare Operating System. Make sure that this driver is correct for the version of NetWare or IntraNetWare that you are using. Restart the server. 20 Hardware Maintenance Manual: Netfinity 4500R Type 8656

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
20
Hardware Maintenance Manual: Netfinity 4500R Type 8656
PCNTNW-NW-054
The adapter did not respond to the initialization command.
Explanation:
The adapter did not respond when the driver tried to initialize
it.
Action:
Verify that the Ethernet controller is enabled. If
the Ethernet controller is enabled, go to “Starting the diagnostic programs”
on page 14 to run the diagnostic programs.
PCNTNW-NW-058
The adapter did not respond to the initialization command.
Explanation:
The interrupt request (IRQ) setting might not be valid or the
EEPROM information might be incorrect.
Action:
Make
sure the IRQ settings are correct in the Configuration/Setup Utility
program. for information on setting the interrupt requests. If the IRQ
settings are correct, go to “Starting the diagnostic programs” on page 14 to
run the diagnostic programs.
PCNTNW-NW-066
The cable might be disconnected from the adapter.
Explanation:
The cable might be disconnected from the server Ethernet port.
Action:
Verify that a cable is connected to the Ethernet port.
PCNTNW-NW-071
The matching virtual adapter could not be found.
Explanation:
You tried to load another instance of the driver with a different
I/O address.
This new adapter could not be found.
Action:
Verify that you installed an IBM Netfinity 10/100 Fault Tolerant
Adapter and make sure that the adapter is seated correctly. If the adapter is
seated correctly, go to “Starting the diagnostic programs” on page 14 to run
the diagnostic programs..
PCNTNW-NW-072
A resource tag is unavailable
.
Explanation:
The driver tried to allocate some resources that were not
available.
Action:
Add more memory, or free some memory
resources in the server. Then, restart the server.
PCNTNW-NW-073
Unable to allocate memory
Explanation:
The driver failed to allocate the memory needed for normal
operation.
Action:
Add more memory, or free some memory
resources in the server. Then, restart the server.
PCNTNW-NW-074
The hardware interrupt cannot be set.
Explanation:
An attempt was made to initialize a given hardware interrupt.
The attempt was not successful.
Action:
Verify that the
Ethernet controller is enabled. If the Ethernet controller is enabled, go to
“Starting the diagnostic programs” on page 14 to run the diagnostic
programs.
If you have an Ethernet adapter installed, make sure that the adapter does
not share an IRQ with any other device.
PCNTNW-NW-075
The Multiple Link Interface Driver (MLID) cannot be registered with the
Link Support Layer (LSL).
Explanation:
An error occurred while the driver was trying to register with
the LSL.
Action:
Check the version of the NetWare or
IntraNetWare Operating System. Make sure that this driver is correct for the
version of NetWare or IntraNetWare that you are using. Restart the server.
Table 2. Novell NetWare or IntraNetWare ODI driver messages for the Ethernet controller.