Home » IBM Manuals » Desktops » IBM 4500R » Manual Viewer

IBM 4500R Hardware Maintenance Manual - Page 30

Network driver interface specification 2.01 (OS/2) driver messages

UPC - 087944567837

Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Table 2. Novell NetWare or IntraNetWare ODI driver messages for the Ethernet controller. PCNTNW-NW-180 The DMA parameter is not necessary for PCI device. Explanation: The Ethernet controller does not require a DMA setting. Action: None necessary, message is for information only. Network driver interface specification 2.01 (OS/2) driver messages This section provides explanations of the error messages for the NDIS 2.01 (OS/2) drivers, and suggested actions to resolve each problem. Table 3. NDIS 2.01 (OS/2) driver messages for the Ethernet controller. PCNTND-1 Unable to open the Protocol Manager. Explanation: The NDIS stack is not configured correctly. and correct your configuration. PCNTND-6 Out of memory while allocating buffers. Action: Check Explanation: The driver could not allocate the requested buffers. Action: Check your system configuration. Edit the PROTOCOL.INI file to reduce the number of Txbuffers and Rxbuffers specified for the driver. PCNTND-7 A Protocol Manager device error occurred. Explanation: The NDIS stack is not configured correctly. and correct your configuration. PCNTND-8 Bad status for the Protocol Manager. Action: Check Explanation: The NDIS stack is not configured correctly in the PROTOCOL.INI file. Action: Check and correct your configuration. PCNTND-9 Cannot find the PROTOCOL.INI entry. Explanation: The NDIS stack is not configured correctly in the PROTOCOL.INI file. Action: Check and correct your configuration. PCNTND-10 The Protocol Manager Input Output Control (IOCTL) failed. Explanation: The NDIS stack is not configured correctly in the PROTOCOL.INI file. Action: Check and correct your configuration. PCNTND-11 Protocol Manager registration failed. Explanation: The NDIS stack is not configured correctly. and correct your configuration. PCNTND-15 Device not found. Action: Check Explanation: The driver cannot find an Ethernet controller in the server. Action: Verify that the Ethernet controller is enabled. If the Ethernet controller is enabled, go to "Starting the diagnostic programs" on page 14 to run the diagnostic programs. PCNTND-16 PCI scan specified, device not found. Explanation: The driver cannot locate the Ethernet controller on the PCI bus. Action: Verify that the Ethernet controller is enabled. If the Ethernet controller is enabled, go to "Starting the diagnostic programs" on page 14 to run the diagnostic programs. 22 Hardware Maintenance Manual: Netfinity 4500R Type 8656

Section	Page
General checkout	9
General information	11
Features and specifications	11
Server features	13
Reliability, availability, and serviceability features	14
Controls and indicators	15
Operator information panel	17
Diagnostics	19
Diagnostic tools overview	19
Identifying problems using LEDs	19
Power supply LEDs	19
Light path diagnostics	19
Diagnostics panel	20
Light path diagnostics table	20
POST	20
POST error messages	21
Event/error logs	21
Small computer system interface messages	21
Diagnostic programs and error messages	21
Text messages	22
Starting the diagnostic programs	22
Viewing the test log	23
Diagnostic error message tables	23
Recovering BIOS	24
Troubleshooting the Ethernet controller	24
Network connection problems	24
Ethernet controller troubleshooting chart	25
Ethernet controller messages	27
Novell NetWare or IntraNetWare server ODI driver messages	27
Network driver interface specification 2.01 (OS/2) driver messages	30
NDIS 4.0 (Windows NT) driver messages	31
UNIX messages	32
Power checkout	34
Replacing the battery	34
Temperature checkout	35
Configuring the server	37
Using the Configuration/Setup Utility program	37
Starting the Configuration/Setup Utility program	37
Choices available from the Configuration/Setup main menu	38
Using passwords	42
Power-on password	42
Administrator password	43
Using the SCSISelect utility program	44
Starting the SCSISelect utility program	44
Choices available from the SCSISelect menu	45
Installing options	47
Exploded view of the Netfinity 4500R	47
System board layout	48
System board options connectors	48
System board internal cable connectors	49
System board external port connectors	49
System board switches and jumpers	50
System board LED locations	52
Before you begin	53
System reliability considerations	54
Working inside a server with power on	54
Handling static-sensitive devices	54
Removing the cover and bezel	55
Working with adapters	56
Adapter considerations	56
Adapter installation instructions	57
Installing internal drives	58
Internal drive bays	59
SCSI drives	60
SCSI IDs	60
Installing a hot-swap drive	60
Installing a non-hot-swap drive	61
Installing a microprocessor	63
Installing a hot-swap power supply	65
Replacing a hot-swap fan assembly	67
Installing the server cover and bezel	68
Connecting external options	68
Cabling requirements	68
Setting SCSI IDs for external devices	69
Installation procedure	69
Input/Output ports	69
Parallel port	70
Viewing or changing the parallel-port assignments	70
Parallel port connector	70
Video port	71
Keyboard port	72
Auxiliary-device (pointing device) port	72
Ultra3 SCSI ports	73
SCSI cabling requirements	73
Setting SCSI IDs	73
SCSI connector pin-number assignments	74
Serial ports	75
Viewing or changing the serial-port assignments	75
Serial-port connectors	75
Universal Serial Bus ports	76
USB cables and hubs	76
USB-port connectors	76
Ethernet port	77
Configuring the Ethernet controller	77
Failover for redundant Ethernet	77
Ethernet port connector	81
Advanced System Management ports	81
Cabling the Server	81
Netfinity Manager	83
Managing your IBM Netfinity server with Netfinity Manager	83
Netfinity Manager documentation	83
Netfinity Manager system requirements	84
Netfinity Manager for OS/2 system requirements	84
Netfinity Manager for Windows 95 and Windows 98 system requirements	84
Netfinity Manager for Windows NT system requirements	85
Starting the Netfinity Manager installation program	86
Netfinity Manager database support	91
DB2 database support	91
System requirements	91
Installing and configuring the database	92
Activating the database	92
Granting and revoking database privileges	93
Deleting the database	95
Lotus Notes database support	95
System requirements	95
Installing the database	96
Browsing the Netfinity Manager Lotus Notes database	97
ODBC database support	97
System requirements	97
ODBC database configuration	98
Creating the Netfinity Manager tables	98
Supported and certified databases	99
Starting Netfinity Manager	100
Netfinity Manager Service Manager	101
Netfinity Manager service descriptions	101
Advanced System Management	101
Alert Manager	102
Alert on LAN configuration	102
Capacity Management	102
Cluster Manager	102
Critical File Monitor	102
DMI Browser	102
ECC Memory Setup	103
Event Scheduler	103
File Transfer	103
Power-On Error Detect	103
Predictive Failure Analysis	103
Process Manager	103
RAID Manager	103
Remote Session	103
Remote System Manager	104
Remote Workstation Control	104
Screen View	104
Security Manager	104
Serial Connection Control	104
Service Configuration Manager	104
Software Inventory	104
System Diagnostics Manager	105
System Information Tool	105
System Monitor	105
System Partition Access	105
System Profile	105
Update Connector Manager	105
Web Manager Configuration	106
Delaying Netfinity Manager startup on OS/2 systems	106
Getting more information about Netfinity Manager	106
Installation options	107
Automated installation	107
Customized installation	108
FRU information (service only)	111
Removing the LED cover	111
Removing the on/off reset board	112
Removing the diskette/CDROM drive	112
Removing the LED board	113
Removing the SCSI backplane assembly	113
Removing the hot-swap hard disk drive backplane	114
Removing the power supply backplane	115
Removing the AC Distribution Box	116
Removing the system board	117
Symptom-to-FRU index	119
Beep symptoms	119
No Beep symptoms	122
Information panel system error LED	122
Diagnostic error codes	124
Error symptoms	128
Power supply LED errors	129
POST error codes	130
SCSI error codes	136
Temperature error messages	136
Fan error messages	137
Power error messages	137
System shutdown	139
Voltage related system shutdown	139
Temperature related system shutdown	139
DASD checkout	140
Host Built-In Self Test (BIST)	140
Bus fault messages	141
Undetermined problems	141
Parts listing (Type 8656)	143
Keyboards	145
Power cords	146
Related service information	149
Safety information	149
General safety	149
Electrical safety	150
Safety inspection guide	151
Handling electrostatic discharge-sensitive devices	152
Grounding requirements	153
Safety notices (multi-lingual translations)	153
Send us your comments!	188
Problem determination tips	189
Notices	189

Match case Limit results 1 per page

Hardware Maintenance Manual: Netfinity 4500R Type 8656

Network driver interface specification 2.01 (OS/2) driver

messages

This section provides explanations of the error messages for the NDIS 2.01 (OS/2)

drivers, and suggested actions to resolve each problem.

PCNTNW-NW-180

The DMA parameter is not necessary for PCI device.

Explanation:

The Ethernet controller does not require a DMA setting.

Action:

None necessary, message is for information only.

Table 3. NDIS 2.01 (OS/2) driver messages for the Ethernet controller.

PCNTND-1

Unable to open the Protocol Manager

Explanation:

The NDIS stack is not configured correctly.

Action:

Check

and correct your configuration.

PCNTND-6

Out of memory while allocating buffers.

Explanation:

The driver could not allocate the requested buffers.

Action:

Check your system configuration. Edit the PROTOCOL.INI file to reduce the number of

Txbuffers and Rxbuffers specified for the driver.

PCNTND-7

A Protocol Manager device error occurred.

Explanation:

The NDIS stack is not configured correctly.

Action:

Check

and correct your configuration.

PCNTND-8

Bad status for the Protocol Manager.

Explanation:

The NDIS stack is not configured correctly in the PROTOCOL.INI file.

Action:

Check and correct your configuration.

PCNTND-9

Cannot find the PROTOCOL.INI entry.

Explanation:

The NDIS stack is not configured correctly in the PROTOCOL.INI file.

Action:

Check and correct your configuration.

PCNTND-10

The Protocol Manager Input Output Control (IOCTL) failed.

Explanation:

The NDIS stack is not configured correctly in the PROTOCOL.INI file.

Action:

Check and correct your configuration.

PCNTND-11

Protocol Manager registration failed.

Explanation:

The NDIS stack is not configured correctly.

Action:

Check

and correct your configuration.

PCNTND-15

Device not found.

Explanation:

The driver cannot find an Ethernet controller in the server.

Action:

Verify that the Ethernet controller is enabled. If the Ethernet controller is enabled, go to

“

Starting the diagnostic programs

”

on page 14 to run the diagnostic programs.

PCNTND-16

PCI scan specified, device not found.

Explanation:

The driver cannot locate the Ethernet controller on the PCI bus.

Action:

Verify that the Ethernet controller is enabled. If the Ethernet controller is enabled, go to

“

Starting the diagnostic programs

”

on page 14 to run the diagnostic programs.

Table 2. Novell NetWare or IntraNetWare ODI driver messages for the Ethernet controller.