IBM 4500R Hardware Maintenance Manual - Page 29

The Multiple Link Interface Driver MLID did not initialize MSMTx Free

Get IBM 4500R - Netfinity - 8656 PDF manuals and user guides
UPC - 087944567837
View all IBM 4500R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Table 2. Novell NetWare or IntraNetWare ODI driver messages for the Ethernet controller. PCNTNW-NW-079 The Multiple Link Interface Driver (MLID) did not initialize MSMTx Free Count. Explanation: The MSMTx Free Count is not initialized correctly. Action: Restart the server. If the problem persists, go to "Starting the diagnostic programs" on page 14 to run the diagnostic programs. . PCNTNW-NW-086 The driver parameter block is too small. Explanation: The driver parameter block is too small. Action: Restart the server. If the problem persists, go to "Starting the diagnostic programs" on page 14 to run the diagnostic programs. PCNTNW-NW-087 The media parameter block is too small. Explanation: The driver media parameter block is too small. Action: Restart the server. If the problem persists, go to "Starting the diagnostic programs" on page 14 to run the diagnostic programs. PCNTNW-NW-091 The hardware configuration conflicts. Explanation: You tried to load a new frame type for the existing controller. The hardware assumptions made in doing so are incorrect. This error can also occur if you try to specify a mode (such as, redundancy) that conflicts with another specified mode. Action: Make sure that your hardware configuration matches the software settings. PCNTNW-NW-126 The group bit in the node address override was cleared. Explanation: The IEEE address has a group bit that indicates that an address belongs to a group of stations. This bit is used only as a destination address; it cannot be used as a source address. You tried to enter a source address with this bit set. The driver cleared the group bit of the source address. Action: None necessary, message is for information only. PCNTNW-NW-127 The local bit in the node address override was set. Explanation: The local bit in the IEEE address format indicates that the addresses are being managed locally. If you use the node address override capabilities of this driver to enter a new address, the local bit must be set. You entered an address without the local bit set. The driver has set the local bit. Action: None necessary, message is for information only. PCNTNW-NW-164 The device was not found. Explanation: The driver cannot find an Ethernet controller in the server. Action: Verify that the Ethernet controller is enabled. If the Ethernet controller is enabled, go to "Starting the diagnostic programs" on page 14 to run the diagnostic programs. PCNTNW-NW-165 The device was not found at IOADDRESS. Explanation: The Ethernet controller cannot be found at the I/O address specified. Action: The Ethernet controller does not require a parameter for the I/O address. Remove the I/O address parameter. PCNTNW-NW-167 PCI scan specified, device not found. Explanation: The driver cannot locate the Ethernet controller on the PCI bus. Action: Verify that the Ethernet controller is enabled. If the problem persists, go to "Starting the diagnostic programs" on page 14 to run the diagnostic programs. Diagnostics 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
Diagnostics
21
PCNTNW-NW-079
The Multiple Link Interface Driver (MLID) did not initialize MSMTx Free
Count.
Explanation:
The MSMTx Free Count is not initialized correctly.
Action:
Restart the server. If the problem persists, go to
“
Starting the
diagnostic programs
”
on page 14 to run the diagnostic programs. .
PCNTNW-NW-086
The driver parameter block is too small.
Explanation:
The driver parameter block is too small.
Action:
Restart the server. If the problem persists, go to
“
Starting the
diagnostic programs
”
on page 14 to run the diagnostic programs.
PCNTNW-NW-087
The media parameter block is too small.
Explanation:
The driver media parameter block is too small.
Action:
Restart the server. If the problem persists, go to
“
Starting the
diagnostic programs
”
on page 14 to run the diagnostic programs.
PCNTNW-NW-091
The hardware configuration conflicts.
Explanation:
You tried to load a new frame type for the existing controller.
The hardware assumptions made in doing so are incorrect. This error can
also occur if you try to specify a mode (such as, redundancy) that conflicts
with another specified mode.
Action:
Make sure that
your hardware configuration matches the software settings.
PCNTNW-NW-126
The group bit in the node address override was cleared.
Explanation:
The IEEE address has a group bit that indicates that an address
belongs to a group of stations. This bit is used only as a destination address;
it cannot be used as a source address. You tried to enter a source address
with this bit set. The driver cleared the group bit of the source address.
Action:
None necessary, message is for information only.
PCNTNW-NW-127
The local bit in the node address override was set.
Explanation:
The local bit in the IEEE address format indicates that the
addresses are being managed locally. If you use the node address override
capabilities of this driver to enter a new address, the local bit must be set.
You entered an address without the local bit set. The driver has set the local
bit.
Action:
None necessary, message is for
information only.
PCNTNW-NW-164
The device was not found.
Explanation:
The driver cannot find an Ethernet controller in the server.
Action:
Verify that the Ethernet controller is enabled. If the Ethernet
controller is enabled, go to
“
Starting the diagnostic programs
”
on page 14 to
run the diagnostic programs.
PCNTNW-NW-165
The device was not found at IOADDRESS.
Explanation:
The Ethernet controller cannot be found at the I/O address
specified.
Action:
The Ethernet controller does not require a
parameter for the I/O address. Remove the I/O address parameter.
PCNTNW-NW-167
PCI scan specified, device not found.
Explanation:
The driver cannot locate the Ethernet controller on the PCI bus.
Action:
Verify that the Ethernet controller is enabled. If the problem persists,
go to
“
Starting the diagnostic programs
”
on page 14 to run the diagnostic
programs.
Table 2. Novell NetWare or IntraNetWare ODI driver messages for the Ethernet controller.