Mackie D8B Owners Manual - Page 126

D8B–HDR24/96 Setup, This example describes the analog hookup for, the D8B-HDR24/96 combination.

Get Mackie D8B PDF manuals and user guides View all Mackie D8B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 126 highlights

D8B-HDR24/96 Setup Hookups This section shows how the D8B is connected to the Mackie HDR24/96. These examples assume that the rest of your studio equipment (monitors, sound sources, outboard processing, etc.) is already connected. Before you begin, note how the three eightchannel I/O cards are arranged on the HDR24/96 rear panel: 1-8 is on the left, 9-16 is in the center, and 17-24 is on the right. Labeling cables before you begin will make connecting the HDR24/96 to your D8B easier. The specific hookups for each D8B and HDR24/96 I/O card are shown below. Analog Hookup to HDR24/96 (AIO•8) This example describes the analog hookup for the D8B-HDR24/96 combination. Cables & Hardware (3) AIO•8 cards for HDR24/96 (3) AIO•8 cards for D8B (6) DB25 to DB25 analog snakes Hookup 1. Connect three snakes between the HDR24/96 Inputs (bottom connector) and the corresponding D8B Tape Outputs (top connector). 2. Connect three snakes between the HDR24/96 Outputs (top connector) and the corresponding D8B Tape Inputs (bottom connector). HDR24/96 Settings 1. Set the Sample Clock to Internal. 2. Set the Sample Rate and Bit Depth according to your preference. It is not necessary to set the D8B and HDR24/96 to the same Sample Rate since, with analog connections, the sample clocks on the two units are not synchronized. Console Settings 1. Set the D8B Sample Rate to 44.1kHz or 48kHz, and set the Apogee Clock to Internal (in the Digital I/O Setup window). This example describes the hookup for the D8B console equipped for analog I/O. AIO•8 Cards HDR 24/96 ANALOG I/O ANALOG I/O ANALOG I/O (6) DB25 to DB25 Analog Snakes Digital 8•Bus ANALOG I/O ANALOG I/O ANALOG I/O AIO•8 Cards OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT INPUT INPUT INPUT Note: Some older AIO•8 cards have the Input jack labeled as "From Tape" and the Output jack labeled as "To Tape." Otherwise, they operate identically. Sigh ... long story. TAPE IN/OUTS D8B Manual • Chapter 4 • page 120 INPUT INPUT INPUT TAPE IN/OUTS

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
D8B Manual • Chapter 4 • page
120
This example describes the hookup for the D8B console equipped for analog I/O.
D8B–HDR24/96 Setup
Hookups
This section shows how the D8B is connected
to the Mackie HDR24/96. These examples assume
that the rest of your studio equipment (monitors,
sound sources, outboard processing, etc.) is
already connected.
Before you begin, note how the three eight-
channel I/O cards are arranged on the HDR24/96
rear panel: 1-8 is on the left, 9-16 is in the center,
and 17-24 is on the right. Labeling cables before
you begin will make connecting the HDR24/96 to
your D8B easier.
The specific hookups for each D8B and
HDR24/96 I/O card are shown below.
Analog Hookup to HDR24/96 (AIO•8)
This example describes the analog hookup for
the D8B–HDR24/96 combination.
Cables & Hardware
(3) AIO•8 cards for HDR24/96
(3) AIO•8 cards for D8B
(6) DB25 to DB25 analog snakes
Hookup
1.
Connect three snakes between the
HDR24/96 Inputs (bottom connector)
and the corresponding D8B Tape
Outputs (top connector).
2.
Connect three snakes between the
HDR24/96 Outputs (top connector)
and the corresponding D8B Tape
Inputs (bottom connector).
HDR24/96 Settings
1.
Set the
Sample Clock
to
Internal
.
2.
Set the
Sample Rate
and
Bit Depth
according to your preference. It is not
necessary to set the D8B and
HDR24/96 to the same
Sample Rate
since, with analog connections, the
sample clocks on the two units are not
synchronized.
Console Settings
1.
Set the D8B
Sample Rate
to
44.1kHz
or
48kHz
, and set the
Apogee Clock
to
Internal
(in the Digital I/O Setup
window).
TAPE IN/OUTS
INPUT
OUTPUT
INPUT
OUTPUT
INPUT
OUTPUT
ANALOG I/O
ANALOG I/O
ANALOG I/O
TAPE IN/OUTS
INPUT
OUTPUT
INPUT
OUTPUT
INPUT
OUTPUT
ANALOG I/O
ANALOG I/O
ANALOG I/O
(6) DB25 to
DB25 Analog
Snakes
Digital 8•Bus
HDR 24/96
AIO
•
8 Cards
AIO
•
8 Cards
Note:
Note:
Note:
Note:
Note:
Some older
AIO•8 cards have the
Input jack labeled as
“From Tape” and the
Output jack labeled
as “To Tape.” Other-
wise, they operate
identically.
Sigh ...
long story.