Sony PDWHD1500 User Manual (PDW-HD1500 / F1600 Operation Manual for Firmware V - Page 28

Rear Panel Chapter 2 Names and Functions of Parts 1 Power supply section (see page 29) 2 Analog audio signal input/ output section (see page 30) 3 Digital audio signal input/ output section (see page 30) 1 (i.LINK) S400 connector POWER AC IN REMOTE DC IN 12V= ANALOG AUDIO INPUT 1 2 ANALOG AUDIO OUTPUT 1 2 AUDIO MONITOR R L DIGITAL AUDIO (AES/EBU) SD/HDSDI INPUT IN 1/2 3/4 1 HDSDI OUTPUT 2 (SUPER) OUT SDSDI OUTPUT 1 2 (SUPER) COMPOSITE OUTPUT 1 2 (SUPER) 1/2 3/4 S400 VIDEO CONTROL REMOTE(9P) MAINTENANCE REF.VIDEO INPUT IN TIME CODE IN OUT 2 VIDEO CONTROL connector 3 REMOTE(9P) connector 4 DC IN 12V connector 5 REMOTE connector 6 SD/HDSDI INPUT connector 7 HDSDI OUTPUT 1, 2 (SUPER) connectors 8 COMPOSITE OUTPUT1, 2 (SUPER) connectors 9 REF.VIDEO INPUT connectors 4 Timecode input/output section (see page 30) 0 (network) connector qa MAINTENANCE connectors qs SDSDI OUTPUT1, 2 (SUPER) connectors a (i.LINK) S400 connector (6-pin, IEEE1394 compliant) Connect a computer or other device, using an i.LINK cable. When the PDBK-201 option board is installed, i.LINK TS (HDV) signals can be input and output via this connector. Notes • When this unit is connected to a device with a 6-pin i.LINK connector by an i.LINK cable, before unplugging the i.LINK cable, first power off the device and disconnect the power plug from the outlet. If the i.LINK cable is unplugged with the device power plug still connected, a current from an excessive voltage (8 to 40 V) output from the i.LINK connector of the device flows into this unit. This may cause a failure of the unit. • When connecting this unit to a device with a 6-pin i.LINK connector, connect to the 6-pin i.LINK connector of the other device first. b VIDEO CONTROL connector (D-sub-9-pin) Connect an HKDV-900 video control unit. See page 174 for correspondence between setting items of HKDV-900 and setup menu of this unit. c REMOTE(9P) (remote control 9-pin) connector (D-sub 9-pin) To control this unit from a controller or VTR supporting the RS-422A Sony 9-pin VTR protocol, connect the device to this connector. d DC IN 12V connector (XLR 4-pin, male) Connect to a DC power source of 12 V. When using the BKP-L551 Battery Adaptor to mount a battery pack, connect the power cable of the BKP-L551. For details, see "Supplying power" on page 32. e REMOTE connector (4-pin) Supplies power to the RM-280 Editing Controller. f SD/HDSDI INPUT (SDSDI/HDSDI signal input) connector (BNC type) This inputs an SDSDI or HDSDI format video/audio signal. g HDSDI OUTPUT 1, 2 (SUPER) (HDSDI signal output 1, 2 (superimpose)) connectors (BNC type) These output HDSDI format video/audio signals. When editing with two PDW-HD1500 units, connect a cable between these connectors on the player unit and the SD/HDSDI INPUT connector on the recorder unit. You can superimpose timecodes, menu settings, error messages, or other information on the output of the HDSDI OUTPUT 2 (SUPER) connector with the setting for CHAR SEL on the HOME page of the function menu or with the setting for setup menu item 028 HD CHARACTER. You can always disable to superimpose the data independent of the setting for CHAR SEL with the setting for setup menu item 028. See "Basic Operations of the Function Menu" (page 48) for more information about the CHAR SEL settings. 28 Rear Panel