Brother International BAS-411 Instruction Manual - English - Page 15

positioned

Get Brother International BAS-411 PDF manuals and user guides View all Brother International BAS-411 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

10 El Adjusting needle bar height 9mm Tighten screw so that clearance is the same at all points. needle bar guide rail oi This part should not contact anything nearby. . D needle bar guide rail 1) Lower the needle bar to its lowest position. When the needle tip is raised 9 mm above the center of the rotary hook shaft, tighten the screw of the needle bar clamp ® so that the screw 0 leans to the right 25° 30°. 2) Lower the needle bar to its lowest position. Lightly press the stopper ® to the cushion rubber 0 side. Then tighten the screw so that it is positioned in the front. [NOTE] Make sure that the stopper does not strike the needle bar guide rail. -11-

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
10
El
Adjusting
needle
bar
height
Tighten
screw
so
that
clearance
is
the
same
at
all
points.
needle
bar
guide
rail
9mm
This
part
should
not
contact
.
D
anything
nearby.
o
i
needle
bar
guide
rail
1)
Lower
the
needle
bar
to
its
lowest
position.
When
the
needle
tip
is
raised
9
mm
rotary
hook
shaft,
tighten
the
screw
of
the
needle
bar
clamp
®
so
that
the
screw
30°.
2)
Lower
the
needle
bar
to
its
lowest
position.
Lightly
press
the
stopper
®
to
the
Then
tighten
the
screw
so
that
it
is
positioned
in
the
front.
[NOTE]
Make
sure
that
the
stopper
does
not
strike
the
needle
bar
guide
rail.
above
the
center
of
the
0
leans
to
the
right
25°
cushion
rubber
0
side.
—11—