Brother International BAS-411 Instruction Manual - English - Page 8
Installing, guard, Setting, machine
 |
View all Brother International BAS-411 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 8 highlights
Attach the screws 0 so that the panel is in the best position for the operator to use. El Installing guard bar 1) Loosen the screws, and covers RD 0 and LD @. 2) Insert the guard bar © and attach it with the bolt and washer from the bottom side of the frame. 3) Install covers RD 0 and LD @ with the screws. 0 El Setting up machine Needle bar case side Before shipping, the machine is set as shown in the figure on the left. Turn the clutch knurl 0 until its red mark © is on the needle bar case side. The machine will be in the automatic jump condition. This is the standard condition of the machine. [NOTE] Refer to the note on P.32 " W Preparation of machine (1)." -4-
-
1 -
2
-
3 -
4 -
5 -
6 -
7 -
8 -
9 -
10 -
11 -
12 -
13 -
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
 |
 |
Attach
the
screws
0
so
that
the
panel
is
in
the
best
position
for
the
operator
to
use.
El
Installing
guard
bar
0
El
Setting
up
machine
Needle
bar
case
side
1)
Loosen
the
screws,
and
covers
RD
0
and
LD
@.
2)
Insert
the
guard
bar
©
and
attach
it
with
the
bolt
and
washer
from
the
bottom
side
of
the
frame.
3)
Install
covers
RD
0
and
LD
@
with
the
screws.
Before
shipping,
the
machine
is
set
as
shown
in
the
figure
on
the
left.
Turn
the
clutch
knurl
0
unti
l
its
red
mark
©
is
on
the
needle
bar
case
side.
The
machine
will
be
in
the
automatic
jump
condition.
This
is
the
standard
condition
of
the
machine.
[NOTE]
Refer
to
the
note
on
P.32
"
W
Preparation
of
machine
(1)."
-4-