Home » HP Manuals » Multifunction Devices » HP CB536A » Manual Viewer

HP CB536A User Guide - Page 128

Use the fax cord that came with the product in order to ensure that the product functions, correctly.

Add to My Manuals
Save this manual to your list of manuals

Page 128 highlights

NOTE: Use the fax cord that came with the product in order to ensure that the product functions correctly. Problem Cause Solution The product cannot receive faxes from The extension-telephone setting might Change the extension-telephone setting. an extension telephone. be disabled. The fax cord might not be securely connected. Verify that the fax cord is securely connected between the telephone jack and the product (or another device that is connected to the product). Press 1-2-3 in sequence, wait for three seconds, and then hang up. The product dialing mode might be incorrectly set, or the extension phone might be incorrectly set. Verify that the product dialing mode is set to Tone. Verify that the extension phone is set up for tone dialing as well. The product is not answering incoming The answer mode might be set to fax calls. Manual. If the answer mode is set to Manual, the product does not answer calls. Start the fax-receiving process manually. The rings-to-answer setting might not be Check the rings-to-answer setting to set correctly. verify that it is set properly. The answer-ring pattern feature might be turned on, but you do not have the service, or you do have the service and the feature is not set correctly. Check the answer-ring pattern feature to verify that it is set properly. The fax cord might not be correctly See the getting started guide to check connected, or the fax cord is not working. the installation. Verify that you are using the fax cord that came with the product. The product might not be able to detect incoming fax tones because the answering machine is playing a voice message. Re-record the answering machine message, leaving at least two seconds of silence at the beginning of the message. Too many devices might be connected to the telephone line. Do not attach more than three devices to the line. Remove the last device that was connected and determine whether the product works. If not, continue removing devices one at a time and retry after removing each one. The telephone line might not be working. Do one of the following: ● Increase the volume on the product, and then press Start Fax on the control panel. If a dial tone exists, the telephone line is working. ● Disconnect the product from the telephone jack, and then connect a telephone. Try to make a telephone call to verify that the telephone line is working. 118 Chapter 10 Fax ENWW

Section	Page
Product basics	11
Product comparison	12
Product features	13
Product walkaround	14
Front view	14
Back view	14
Interface ports	15
Serial number and model number location	15
Supported operating systems	16
Supported product software	16
Software included with the product	16
Easy installation for Windows	16
Advanced installation	16
Macintosh software	17
Supported printer drivers	17
Control panel	19
Control-panel walkaround	20
Control-panel menus	21
Use the control-panel menus	21
Control-panel main menus	21
Software for Windows	29
Supported operating systems for Windows	30
Printer driver	30
Priority for print settings	30
Open the printer driver and change the print settings	31
Software installation types for Windows	32
Remove software for Windows	32
Supported utilities for Windows	33
HP Toolbox software	33
Status Alerts software	33
Other Windows components and utilities	33
Use the product with Macintosh	35
Software for Macintosh	36
Supported operating systems for Macintosh	36
Supported printer drivers for Macintosh	36
Priority for print settings for Macintosh	36
Change printer-driver settings for Macintosh	36
Software installation types for Macintosh	37
Install Macintosh software for direct connections (USB)	37
Use features in the Macintosh printer driver	38
Print	38
Create and use printing presets in Macintosh	38
Resize documents or print on a custom paper size	38
Print a cover page	38
Use watermarks	39
Print multiple pages on one sheet of paper in Macintosh	39
Print on both sides of the page (duplex printing)	39
Scan from the product and HP Director (Macintosh)	41
Scanning tasks	41
Fax a document from a Macintosh computer	42
Connectivity	43
Connect the product directly to a computer with USB	44
Paper and print media	45
Understand paper and print media use	46
Supported paper and print media sizes	47
Special paper or print media guidelines	48
Load paper and print media	49
Priority input tray	49
Tray 1	49
Configure trays	51
Print tasks	53
Change the print driver to match the media type and size	54
Supported paper types and tray capacity	54
Get help for any print option	55
Cancel a print job	56
Change the default settings	57
Create booklets	58
Change print-quality settings	58
Change print density	58
Print on special media	59
Use different paper and print covers	60
Print a blank first page	60
Resize documents	61
Select a paper size	61
Select a paper source	61
Select a paper type	61
Set the print orientation	62
Use watermarks	62
Save toner	62
Print on both sides of the paper (duplex printing)	63
Print multiple pages on one sheet of paper in Windows	65
Economy settings	66
EconoMode	66
Archive print	66
Copy	67
Load originals	68
Use copy	69
One-touch copy	69
Multiple copies	69
Cancel a copy job	69
Reduce or enlarge copies	69
Copy settings	70
Copy quality	70
Adjust the lighter/darker (contrast) setting	71
Change copy job print density	72
Define custom copy settings	72
Print or copy edge-to-edge	72
Copy onto media of different types and sizes	72
Restore the copy-settings defaults	73
Duplex (two-sided) copy jobs	74
Scan	77
Load originals for scanning	78
Use scan	79
Scan methods	79
Scan by using HP LaserJet Scan (Windows)	79
Scan by using other software	79
Scan from a TWAIN-compliant program	79
Scan from a WIA-compliant program (Windows XP and Vista only)	79
Scanning by using optical character recognition (OCR) software	80
Readiris	80
Canceling a scan job	80
Scan settings	81
Scan file format	81
Scanner resolution and color	81
Resolution and color guidelines	82
Color	82
Scan quality	82
Fax	85
Fax features	86
Setup	87
Install and connect the hardware	87
Connect to a telephone line	87
Connect additional devices	87
Set up fax with a telephone answering machine	89
Setup for stand-alone fax	89
Configure fax settings	89
Use the control panel to set the fax time, date, and header	90
Use HP Fax Setup Wizard to set the fax time, date, and header	90
Use of common localized letters in fax headers	90
Manage the phone book	91
Use phone-book data from other programs	91
Delete phone book	92
Special dialing symbols and options	92
Manage speed dials	92
Create and edit speed dials	92
Delete speed dials	93
Manage group-dial entries	94
Create and edit group-dial entries	94
Delete group-dial entries	94
Delete an individual from a group-dial entry	94
Set fax polling	95
Change fax settings	96
Set the sound-volume settings	96
Set the alert volume	96
Set the fax-sounds (phone-line) volume	96
Set the ring volume	96
Set the handset volume	97
Send fax settings	97
Set a dial prefix	97
Set the dial-tone detection	97
Set autoredial	98
Set light/dark and resolution	98
Set the default light/dark (contrast) setting	98
Set resolution settings	99
Set tone-dialing or pulse-dialing	100
Receive fax settings	100
Set or change number of rings-to-answer	100
Use the rings-to-answer setting	100
Set the number of rings-to-answer	101
Set the answer mode	101
Set fax forwarding	101
Set up distinctive ring	102
Use the private receive feature	102
Set up the computer to receive faxes	103
Use autoreduction for incoming faxes	104
Set the silence-detect mode	104
Set the default fax reprint settings	104
Create stamp-received faxes	105
Block or unblock fax numbers	105
Make an extension telephone available to receive faxes	106
Use fax	107
Fax software	107
Supported fax programs	107
Available cover-page templates	107
Customize a fax cover sheet	107
Cancel a fax	107
Cancel the current fax	107
Cancel a pending fax job	108
Delete faxes from memory	108
Use fax on a DSL, PBX, ISDN, or VoIP system	108
DSL	108
PBX	109
ISDN	109
VoIP	109
Send a fax	109
Fax from the automatic document feeder (ADF)	109
Manual dial faxing	111
Use speed dials and group-dial entries	112
Send a fax by using a speed dial	112
Send a fax by using a group-dial entry	112
Send a fax from the software	114
Send a fax by dialing from a downstream phone	116
Send a delayed fax	116
Use access codes, credit cards, or calling cards	117
Send faxes internationally	117
Receive a fax	117
Print a stored fax (when private receive feature is on)	117
Reprint a fax	117
Receive a fax when the handset rings	118
Receive faxes when fax tones are audible on the phone line	118
View a fax that was sent to your computer	118
Solve fax problems	119
Fax error messages	119
Alert and warning message tables	119
Fax memory is retained when there is a loss of power	123
Fax logs and reports	123
Print all fax reports	123
Print individual fax reports	123
Set the fax activity log to print automatically	124
Set the fax error report	124
Set the fax confirmation report	125
Include the first page of each fax on the fax confirmation, fax error, and last call reports	125
Change error correction and fax speed	125
Set the fax-error-correction mode	125
Change the fax speed	126
Problems sending faxes	126
Problems receiving faxes	127
Performance problems	130
Manage and maintain the product	131
Information pages	132
Use the HP Toolbox software	133
View HP Toolbox	133
Status	134
Fax	135
Fax tasks	135
Fax phone book	135
Fax send log	137
Fax receive log	137
Shop for Supplies	138
Other Links	138
Manage supplies	139
Check and order supplies	139
Check supplies status by using the control panel	139
Store supplies	140
HP policy on non-HP supplies	140
HP fraud hotline	140
Recycle supplies	140
Redistribute toner	141
Replace supplies	141
Print cartridge	141
Clean the product	142
Clean the paper path	142
Clean the exterior	143
Firmware updates	143
Problem solve	145
Problem-solving checklist	146
Restore the factory-set defaults	147
Control-panel messages	148
Alert and warning messages	148
Alert and warning message tables	148
Critical error messages	149
Critical error message-tables	149
Control-panel display problems	151
Clear jams	151
Causes of jams	151
Where to look for jams	152
Clear jams from the ADF	152
Clear jams from the input-tray areas	153
Clear jams from the output bin	155
Clear jams from the print-cartridge area	156
Avoid repeated jams	157
Solve image-quality problems	158
Print problems	158
Print quality problems	158
General print-quality issues	158
Media-handling problems	162
Print-media guidelines	162
Solve print-media problems	163
Performance problems	164
Copy problems	165
Prevent copy problems	165
Image problems	166
Media-handling problems	167
Performance problems	168
Scan problems	169
Solve scanned-image problems	169
Scan-quality problems	171
Prevent scan-quality problems	171
Solve scan-quality problems	171
Fax problems	171
Optimize and improve image quality	171
Print-quality checklist	171
Manage and configure printer drivers	172
Temporarily change print-quality settings	172
Change print-quality settings for all future jobs	172
Solve connectivity problems	173
Solve direct-connection problems	173
Solve software problems	174
Solve common Windows problems	174
Solve common Macintosh problems	174
Accessories and ordering information	177
Supplies	178
Cable and interface accessories	178
Service and support	179
Hewlett-Packard limited warranty statement	179
Customer self repair warranty service	180
Print cartridge limited warranty statement	181
Customer support	181
Repack the device	181
Specifications	183
Physical specifications	184
Electrical specifications	184
Power consumption	184
Environmental specifications	185
Acoustic emissions	185
Regulatory information	187
FCC compliance	188
Environmental product stewardship program	189
Protecting the environment	189
Ozone production	189
Power consumption	189
Toner consumption	189
Paper use	189
Plastics	189
HP LaserJet print supplies	189
Return and recycling instructions	190
United States and Puerto Rico	190
Multiple returns (two to eight cartridges)	190
Single returns	190
Shipping	190
Non-US returns	190
Paper	190
Material restrictions	190
Disposal of waste equipment by users in private households in the European Union	191
Chemical substances	191
Material Safety Data Sheet (MSDS)	192
For more information	192
Telephone Consumer Protection Act (United States)	193
IC CS-03 requirements	193
EU statement for telecom operation	194
New Zealand telecom statements	194
Declaration of conformity	195
Safety statements	196
Laser safety	196
Canadian DOC regulations	196
EMI statement (Korea)	196
Laser statement for Finland	197
Substances table (China)	198
Glossary	199

Match case Limit results 1 per page

NOTE:

Use the fax cord that came with the product in order to ensure that the product functions

correctly.

Problem

Cause

Solution

The product cannot receive faxes from

an extension telephone.

The extension-telephone setting might

be disabled.

Change the extension-telephone setting.

The fax cord might not be securely

connected.

Verify that the fax cord is securely

connected between the telephone jack

and the product (or another device that is

connected to the product). Press 1-2-3 in

sequence, wait for three seconds, and

then hang up.

The product dialing mode might be

incorrectly set, or the extension phone

might be incorrectly set.

Verify that the product dialing mode is set

Tone

. Verify that the extension phone

is set up for tone dialing as well.

The product is not answering incoming

fax calls.

The answer mode might be set to

Manual

If the answer mode is set to

Manual

, the

product does not answer calls. Start the

fax-receiving process manually.

The rings-to-answer setting might not be

set correctly.

Check the rings-to-answer setting to

verify that it is set properly.

The answer-ring pattern feature might be

turned on, but you do not have the

service, or you do have the service and

the feature is not set correctly.

Check the answer-ring pattern feature to

verify that it is set properly.

The fax cord might not be correctly

connected, or the fax cord is not working.

See the getting started guide to check

the installation. Verify that you are using

the fax cord that came with the product.

The product might not be able to detect

incoming fax tones because the

answering machine is playing a voice

message.

Re-record the answering machine

message, leaving at least two seconds of

silence at the beginning of the message.

Too many devices might be connected to

the telephone line.

Do not attach more than three devices to

the line. Remove the last device that was

connected and determine whether the

product works. If not, continue removing

devices one at a time and retry after

removing each one.

The telephone line might not be working.

Do one of the following:

●

Increase the volume on the product,

and then press

Start Fax

on the

control panel. If a dial tone exists,

the telephone line is working.

●

Disconnect the product from the

telephone jack, and then connect a

telephone. Try to make a telephone

call to verify that the telephone line

is working.

118

Chapter 10

Fax

ENWW