HP ProLiant 3000 ProLiant 3000 Servers Maintenance and Service Guide - Page 111

The following ASR-2 flow chart shows you the sequence of events after a hardware or software

Page 111 highlights

3-54 Diagnostic Tools The following ASR-2 flow chart shows you the sequence of events after a hardware or software error occurs: Hardware/Software error occurs | Error records in the Critical Error Log, or the Integrated Management Log, depending on your server configuration. | Operating System halts normal operation | ASR Timer expires | Server is reset | If a modem is installed and paging is enabled, the Server Failure Notification pager alert is sent to the Server Administrator. | Unattended server boots the Operating System ---Or--- Server boots the Compaq Utilities on the system partition on the hard drive  | If the server continues experiencing hardware/software errors and the number of ASR cycles exceed the specified number of recovery attempts, the server logs an error to the Server Health Log or the Integrated Management Log and boots the Compaq Utilities from the system partition on the hard drive. If a modem is installed, ASR puts the modem on auto answer so that the Server Administrator can dial in (using third party terminal emulator software) to remotely run the Compaq Utilities to identify the source of the fault. | Or | Local Server Administrator runs Compaq Utilities from server console to identify the source of the fault Figure 3-1. ASR-2 flow chart

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162

3-54
Diagnostic Tools
The following ASR-2 flow chart shows you the sequence of events after a hardware or software
error occurs:
Hardware/Software error occurs
|
Error records in the Critical Error Log,
or the Integrated Management Log,
depending on your server
configuration.
|
Operating System halts normal
operation
|
ASR Timer expires
|
Server is reset
|
If a modem is installed and paging is
enabled, the Server Failure
Notification pager alert is sent to the
Server Administrator.
|
Unattended server boots the
Operating System
---Or---
Server boots the Compaq Utilities
on the system partition on the hard
drive
|
If the server continues experiencing
hardware/software errors and the
number of ASR cycles exceed the
specified number of recovery
attempts, the server logs an error to
the Server Health Log or the
Integrated Management Log and
boots the Compaq Utilities from the
system partition on the hard drive.
If a modem is installed, ASR puts
the modem on auto answer so that
the Server Administrator can dial in
(using third party terminal emulator
software) to remotely run the
Compaq Utilities to identify the
source of the fault.
|
Or
|
Local Server Administrator runs
Compaq Utilities from server
console to identify the source of
the fault
Figure 3-1. ASR-2 flow chart