HP ProLiant 3000 ProLiant 3000 Servers Maintenance and Service Guide - Page 55

Power Switch

Get HP ProLiant 3000 PDF manuals and user guides View all HP ProLiant 3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

2-42 Removal and Replacement Procedures Power Switch IMPORTANT: To completely remove all power from the system, you must disconnect the power cord from the server. In systems with multiple power supplies, you must disconnect all power cords to completely remove power from the system. To remove the power switch: 1. Perform the preparation procedures. See "Preparation Procedures" earlier in this chapter. 2. Remove the front fixed bezel. See "Front Fixed Bezel" earlier in this chapter. 3. Remove the side access panel. See "Side Access Panel" earlier in this chapter. 4. Unplug the power switch cables from the system board. 5. Press on the top and bottom of the switch, from inside the chassis 1, then pull the switch out the front of the server 2. 1 2 1 Figure 2-38. Removing the power switch Reverse steps 1 through 5 to replace the power switch.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
2-42
Removal and Replacement Procedures
Power Switch
IMPORTANT:
To completely remove all power from the system, you must disconnect the
power cord from the server. In systems with multiple power supplies, you must disconnect
all power cords to completely remove power from the system.
To remove the power switch:
1.
Perform the preparation procedures. See “Preparation Procedures” earlier in this chapter.
2.
Remove the front fixed bezel. See “Front Fixed Bezel” earlier in this chapter.
3.
Remove the side access panel. See “Side Access Panel” earlier in this chapter.
4.
Unplug the power switch cables from the system board.
5.
Press on the top and bottom of the switch, from inside the chassis
1
, then pull the switch
out the front of the server
2
.
2
1
1
Figure 2-38. Removing the power switch
Reverse steps 1 through 5 to replace the power switch.