HP ProLiant 3000 ProLiant 3000 Servers Maintenance and Service Guide - Page 40

Diskette Drive, Loosen the two thumbscrews on the underside of the diskette drive

Get HP ProLiant 3000 PDF manuals and user guides View all HP ProLiant 3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

2-27 Diskette Drive The diskette drive is removed for replacement or when installing another media device. To remove the diskette drive: 1. Perform the preparation procedures. See "Preparation Procedures" earlier in this chapter. 2. Remove the top access panel. See "Top Access Panel" earlier in this chapter. 3. Remove the drive cage assembly. See "Drive Cage Assembly" later in this chapter. 4. Disconnect all cables from the diskette drive. 5. Loosen the two thumbscrews on the underside of the diskette drive 1. 6. Remove the screw on the side of the diskette drive 2. 7. Pull the drive back, then out the top of the chassis 3. 2 3 1 Figure 2-23. Removing the diskette drive Reverse steps 1 through 7 to replace the diskette drive. Compaq ProLiant 3000 Servers, for use with Intel 350 MHz or greater processor-based servers only, Maintenance and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
2-27
Compaq ProLiant 3000 Servers, for use with Intel 350 MHz or greater processor-based servers only, Maintenance and Service Guide
Diskette Drive
The diskette drive is removed for replacement or when installing another media device.
To remove the diskette drive:
1.
Perform the preparation procedures. See “Preparation Procedures” earlier in this chapter.
2.
Remove the top access panel. See “Top Access Panel” earlier in this chapter.
3.
Remove the drive cage assembly. See “Drive Cage Assembly” later in this chapter.
4.
Disconnect all cables from the diskette drive.
5.
Loosen the two thumbscrews on the underside of the diskette drive
1
.
6.
Remove the screw on the side of the diskette drive
2
.
7.
Pull the drive back, then out the top of the chassis
3
.
1
2
3
Figure 2-23. Removing the diskette drive
Reverse steps 1 through 7 to replace the diskette drive.