HP ProLiant 3000 ProLiant 3000 Servers Maintenance and Service Guide - Page 34

Simplex Enabler Board

Get HP ProLiant 3000 PDF manuals and user guides View all HP ProLiant 3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

2-21 Simplex Enabler Board The Simplex Enabler board is removed when changing the Wide-Ultra drive cage assembly to Duplex mode. To remove the Simplex Enabler board: 1. Perform the preparation procedures. See "Preparation Procedures" earlier in this chapter. 2. Remove the drive cage assembly. See "Drive Cage Assemblies" earlier in this chapter. 3. Pull the Simplex Enabler board off the plugs on the back of the drive cage assembly. Figure 2-17. Removing the Simplex Enabler Board Reverse steps 1 through 3 to replace the Simplex Enabler board. Duplex Enabler Board The Duplex Enabler board ships in the country specific kit with every Wide-Ultra drive cage assembly. It is removed and replaced using the same steps as the Simplex Enabler board. The Duplex Enabler board has a SCSI connector for removable media use. Before removing the Duplex Enabler board, be sure to disconnect any SCSI cables. Compaq ProLiant 3000 Servers, for use with Intel 350 MHz or greater processor-based servers only, Maintenance and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
2-21
Compaq ProLiant 3000 Servers, for use with Intel 350 MHz or greater processor-based servers only, Maintenance and Service Guide
Simplex Enabler Board
The Simplex Enabler board is removed when changing the Wide-Ultra drive cage assembly to
Duplex mode.
To remove the Simplex Enabler board:
1.
Perform the preparation procedures. See “Preparation Procedures” earlier in this chapter.
2.
Remove the drive cage assembly. See “Drive Cage Assemblies” earlier in this chapter.
3.
Pull the Simplex Enabler board off the plugs on the back of the drive cage assembly.
Figure 2-17. Removing the Simplex Enabler Board
Reverse steps 1 through 3 to replace the Simplex Enabler board.
Duplex Enabler Board
The Duplex Enabler board ships in the country specific kit with every Wide-Ultra drive cage
assembly. It is removed and replaced using the same steps as the Simplex Enabler board. The
Duplex Enabler board has a SCSI connector for removable media use. Before removing the
Duplex Enabler board, be sure to disconnect any SCSI cables.