HP ProLiant 3000 ProLiant 3000 Servers Maintenance and Service Guide - Page 95

Run the System Configuration Utility., Adapter/NVRAM

Get HP ProLiant 3000 PDF manuals and user guides View all HP ProLiant 3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

3-38 Diagnostic Tools DAAD Diagnostic Messages Continued Message Description Accelerator status: Cache was automatically configured during last controller reset. This can occur when cacheboard is replaced with one of a different size. Cache board was probably replaced with one of a different size. Recommended Action Nothing needs to be done. Normal operations should continue. Accelerator status: Valid data found at reset Valid data was found in posted write memory at reinitialization. Data will be flushed to disk. Not an error or data loss condition. No action needs to be taken. Accelerator status: Warranty alert Catastrophic problem with array accelerator board. Refer to other messages on Diagnostics screen for exact meaning of this message. Replace the array accelerator board. Adapter/NVRAM ID mismatch EISA nonvolatile RAM has an ID for a different controller from the one physically present in the slot. Run the System Configuration Utility. Battery X not fully Battery is not fully charged. charged Allow 36 hours to recharge them. Board not attached Array controller configured for use with array accelerator board, but one is not attached. Attach array accelerator board to array controller. NVRAM configuration present, controller not detected EISA nonvolatile RAM has a configuration for an array controller but there is no board in this slot. Either a board has been removed from the system or a board has been placed in the wrong slot. Place the array controller in the proper slot or run the System Configuration Utility to reconfigure nonvolatile RAM to reflect the removal or new position. Compatibility port problem detected Compatibility port configured for this IDA controller. When DAAD was verifying this interface, a serious problem was detected. A hardware problem has occurred; replace the IDA controller. Continued

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
3-38
Diagnostic Tools
DAAD Diagnostic Messages
Continued
Message
Description
Recommended Action
Accelerator
status: Cache was
automatically
configured during
last controller
reset. This can
occur when
cacheboard is
replaced with one
of a different size.
Cache board was probably replaced with
one of a different size.
Nothing needs to be done. Normal operations should
continue.
Accelerator
status: Valid data
found at reset
Valid data was found in posted write
memory at reinitialization. Data will be
flushed to disk.
Not an error or data loss condition. No action needs
to be taken.
Accelerator
status: Warranty
alert
Catastrophic problem with array
accelerator board. Refer to other
messages on Diagnostics screen for exact
meaning of this message.
Replace the array accelerator board.
Adapter/NVRAM
ID mismatch
EISA nonvolatile RAM has an ID for a
different controller from the one physically
present in the slot.
Run the System Configuration Utility.
Battery X not fully
charged
Battery is not fully charged.
Allow 36 hours to recharge them.
Board not
attached
Array controller configured for use with
array accelerator board, but one is not
attached.
Attach array accelerator board to array controller.
NVRAM
configuration
present, controller
not detected
EISA nonvolatile RAM has a configuration
for an array controller but there is no
board in this slot. Either a board has been
removed from the system or a board has
been placed in the wrong slot.
Place the array controller in the proper slot or run the
System Configuration Utility to reconfigure nonvolatile
RAM to reflect the removal or new position.
Compatibility port
problem detected
Compatibility port configured for this IDA
controller. When DAAD was verifying this
interface, a serious problem was detected.
A hardware problem has occurred; replace the IDA
controller.
Continued