HP ProLiant 3000 ProLiant 3000 Servers Maintenance and Service Guide - Page 69

Automatic Data Recovery is in, Run Diagnostics. Replace failed

Get HP ProLiant 3000 PDF manuals and user guides View all HP ProLiant 3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

3-12 Diagnostic Tools POST Error Messages Continued Error Code Audible Beeps L=Long S=Short Probable Source of Problem 1778-Drive Array resuming Automatic Data Recovery process None This message appears whenever a controller reset or power cycle occurs while Automatic Data Recovery is in progress. Recommended Action No action necessary. 1779-Drive Array Controller detects replacement drives None Intermittent drive failure and/or If this message appears and drive X possible loss of data. has not been replaced, this indicates an intermittent drive failure. This message also appears once immediately following drive replacement whenever data must be restored from backup. 1780-Disk 0 Failure None Hard drive/format error. Run Diagnostics. Replace failed assembly as indicated. 1781-Disk 1 Failure None Hard drive/format error. Run Diagnostics. Replace failed assembly as indicated. 1782-Disk Controller Failure None Hard disk drive circuitry error. Run Diagnostics. Replace failed assembly as indicated. 1784-Drive Array None Defective drive and/or cables. Check for loose cables. Replace Drive Failure, Physical defective drive X and/or cable(s). Drive 1785-Drive Array not Configured None Configuration error. Run the System Configuration Utility and correct. 1786-Drive Array Recovery Needed The following drive(s) need Automatic Data Recovery: Drive X. Select "F1" to continue with recovery of data to drive(s). None Interim Data Recovery mode. Press F1 key to allow Automatic Data Data has not been recovered Recovery to begin. Data will yet. automatically be restored to drive X now that the drive has been replaced or now seems to be working. -Or- Press the F2 key and the system will continue to operate in the Interim Data Recovery mode. Select "F2" to continue without recovery of data to drive(s). Continued

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
3-12
Diagnostic Tools
POST Error Messages
Continued
Error Code
Audible Beeps
L=Long
S=Short
Probable Source of Problem
Recommended Action
1778-Drive Array
resuming Automatic
Data Recovery
process
None
This message appears
whenever a controller reset or
power cycle occurs while
Automatic Data Recovery is in
progress.
No action necessary.
1779-Drive Array
Controller detects
replacement drives
None
Intermittent drive failure and/or
possible loss of data.
If this message appears and drive
X
has not been replaced, this indicates
an intermittent drive failure. This
message also appears once
immediately following drive
replacement whenever data must be
restored from backup.
1780-Disk 0 Failure
None
Hard drive/format error.
Run Diagnostics. Replace failed
assembly as indicated.
1781-Disk 1 Failure
None
Hard drive/format error.
Run Diagnostics. Replace failed
assembly as indicated.
1782-Disk Controller
Failure
None
Hard disk drive circuitry error.
Run Diagnostics. Replace failed
assembly as indicated.
1784-Drive Array
Drive Failure, Physical
Drive
None
Defective drive and/or cables.
Check for loose cables. Replace
defective drive
X
and/or cable(s).
1785-Drive Array not
Configured
None
Configuration error.
Run the System Configuration Utility
and correct.
1786-Drive Array
Recovery Needed
The following drive(s)
need Automatic Data
Recovery: Drive
X.
Select "F1" to
continue with
recovery of data to
drive(s).
Select "F2" to
continue without
recovery of data to
drive(s).
None
Interim Data Recovery mode.
Data has not been recovered
yet.
Press
F1
key to allow Automatic Data
Recovery to begin. Data will
automatically be restored to drive
X
now that the drive has been replaced
or now seems to be working.
-Or-
Press the
F2
key and the system will
continue to operate in the Interim Data
Recovery mode.
Continued