HP ProLiant 3000 ProLiant 3000 Servers Maintenance and Service Guide - Page 48

Processor, Compaq ProLiant 3000 Servers support up to two 500 MHz or greater Intel Pentium III Xeon

Get HP ProLiant 3000 PDF manuals and user guides View all HP ProLiant 3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

2-35 Processor Compaq ProLiant 3000 Servers support up to two 500 MHz or greater Intel Pentium III Xeon processors with corresponding processor power modules and memory banks. To remove a processor: 1. Perform the preparation procedures. See "Preparation Procedures" earlier in this chapter. 2. Remove the side access panel. See "Side Access Panel" earlier in this chapter. 3. Remove the top access panel. See "Top Access Panel" earlier in this chapter. 4. Push the two locking clips 1 in to release the processor. 5. Remove the processor 2. NOTE: The processor may be a different model than illustrated. 2 1 1 Figure 2-31. Removing a processor Reverse steps 1 through 5 to replace the processor. NOTE: The locking clips lock into place when the processor is properly seated. Compaq ProLiant 3000 Servers, for use with Intel 350 MHz or greater processor-based servers only, Maintenance and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
2-35
Compaq ProLiant 3000 Servers, for use with Intel 350 MHz or greater processor-based servers only, Maintenance and Service Guide
Processor
Compaq ProLiant 3000 Servers support up to two 500 MHz or greater Intel Pentium III Xeon
processors with corresponding processor power modules and memory banks.
To remove a processor:
1.
Perform the preparation procedures. See “Preparation Procedures” earlier in this chapter.
2.
Remove the side access panel. See “Side Access Panel” earlier in this chapter.
3.
Remove the top access panel. See “Top Access Panel” earlier in this chapter.
4.
Push the two locking clips
1
in to release the processor.
5.
Remove the processor
2
.
NOTE
:
The processor may be a different model than illustrated.
1
1
2
Figure 2-31. Removing a processor
Reverse steps 1 through 5 to replace the processor.
NOTE
:
The locking clips lock into place when the processor is properly seated.