HP ProLiant 3000 ProLiant 3000 Servers Maintenance and Service Guide - Page 47

Netelligent 10/100 TX UTP PCI Controller

Get HP ProLiant 3000 PDF manuals and user guides View all HP ProLiant 3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

2-34 Removal and Replacement Procedures Netelligent 10/100 TX UTP PCI Controller The Compaq Netelligent 10/100 TX UTP network controller is removed for replacement or to access the system I\O board. To remove a Netelligent 10/100 TX UTP PCI controller: 1. Perform the preparation procedures. See "Preparation Procedures" earlier in this chapter. 2. Remove the side access panel. See "Side Access Panels" earlier in this chapter. 3. Disconnect any external cables from the PCI controller. 4. Open the slot release lever by pressing on its ribbed area 1. 5. Grasp each end of the PCI controller, then gently remove it without touching other installed boards 2. 2 1 Figure 2-30. Removing a Netelligent 10/100 TX UTP PCI Controller Reverse steps 1 through 5 to replace a Netelligent 10/100 TX UTP PCI Controller. 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
2-34
Removal and Replacement Procedures
Netelligent 10/100 TX UTP PCI Controller
The Compaq Netelligent 10/100 TX UTP network controller is removed for replacement or to
access the system I\O board.
To remove a Netelligent 10/100 TX UTP PCI controller:
1.
Perform the preparation procedures. See “Preparation Procedures” earlier in this chapter.
2.
Remove the side access panel. See “Side Access Panels” earlier in this chapter.
3.
Disconnect any external cables from the PCI controller.
4.
Open the slot release lever by pressing on its ribbed area
1
.
5.
Grasp each end of the PCI controller, then gently remove it without touching other
installed boards
2
.
3
1
2
Figure 2-30. Removing a Netelligent 10/100 TX UTP PCI Controller
Reverse steps 1 through 5 to replace a Netelligent 10/100 TX UTP PCI Controller.