Yamaha MD4S Owner's Manual - Page 102

Cannot use Part Copy or Part, Cannot play the Cue List

Get Yamaha MD4S PDF manuals and user guides View all Yamaha MD4S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 102 highlights

102 Appendix Symptom Advice Cannot use the punch-in/out or ping-pong recording function! Recordings play back at the wrong pitch! Cannot use Part Copy or Part Erase! In some cases, punch-in or ping-pong recording may not be possible on a song that was edited on an MD recorder other than the MD4S or the Yamaha MD8/MD4. Use the Song Copy function to copy the song, and perform the punch-in/out or ping-pong recording operation on the copy. If the song was recorded on an MD recorder other than the MD4S or the Yamaha MD8/MD4, it is possible that the song may be copyprotected (by SCMS). In this case, it will not be possible to perform punch-in or ping-pong recording. Make sure that the Pitch function is not set to VARI. Make sure that the 1/2 Play function is turned off. Make sure that the Last Record In/Out points have been set. If they have been set, the IN/OUT point indicators will light. Make sure that the Last Record Out point has not been set in a location earlier than the Last Record In point. The signal of the input channel is not output from the AUX SEND jacks! Cannot play the Cue List! MIDI sequencer does not synchronize to the MD4S! Rotate the AUX control toward 1 or 2, and raise the channel fader. Since the signal sent to the AUX SEND jacks is post-fader, no signal will be sent to the AUX SEND jacks unless the channel fader is raised. Make sure not all steps in the Cue List are set for zero repeats (n=0). Make sure that the specified ranges within the cue list are correct. Make sure that no non-existent markers are selected in the cue list. Make sure that your MIDI sequencer supports MTC or MIDI Clock. Make sure that the MIDI sequencer has been set to synchronize to incoming MTC or MIDI Clock messages. If you are using MIDI Clock, make sure that a tempo map has been programmed in the MD4S. (If the measure/beat display does not appear when you press the DISPLAY button, a tempo map has not been set.) Make sure that the MD4S has been set to transmit MTC or MIDI Clock messages from its MIDI OUT connector. When MTC is being transmitted, the MTC SYNC MASTER indicator will light. When MIDI Clock is being transmitted, the MIDI CLK indicator will light. Make sure that X1/2 Play is turned off. If X1/2 Play is on, synchronization is not possible. If you are using a Repeat function such as A-B Repeat, some time may be required for the MIDI sequencer to synchronize during a repeat, due to the slowness of the MD4S locate function. -Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
102
Appendix
—Owner’s Manual
Cannot use the punch-in/out
or ping-pong recording
function!
In some cases, punch-in or ping-pong recording may not be possi-
ble on a song that was edited on an MD recorder other than the
MD4S or the Yamaha MD8/MD4. Use the Song Copy function to
copy the song, and perform the punch-in/out or ping-pong record-
ing operation on the copy.
If the song was recorded on an MD recorder other than the MD4S
or the Yamaha MD8/MD4, it is possible that the song may be copy-
protected (by SCMS). In this case, it will not be possible to perform
punch-in or ping-pong recording.
Recordings play back at the
wrong pitch!
Make sure that the Pitch function is not set to VARI.
Make sure that the 1/2 Play function is turned off.
Cannot use Part Copy or Part
Erase!
Make sure that the Last Record In/Out points have been set. If they
have been set, the IN/OUT point indicators will light.
Make sure that the Last Record Out point has not been set in a loca-
tion earlier than the Last Record In point.
The signal of the input chan-
nel is not output from the
AUX SEND jacks!
Rotate the AUX control toward 1 or 2, and raise the channel fader.
Since the signal sent to the AUX SEND jacks is post-fader, no signal
will be sent to the AUX SEND jacks unless the channel fader is raised.
Cannot play the Cue List!
Make sure not all steps in the Cue List are set for zero repeats (n=0).
Make sure that the speci
fi
ed ranges within the cue list are correct.
Make sure that no non-existent markers are selected in the cue list.
MIDI sequencer does not
synchronize to the MD4S!
Make sure that your MIDI sequencer supports MTC or MIDI Clock.
Make sure that the MIDI sequencer has been set to synchronize to
incoming MTC or MIDI Clock messages.
If you are using MIDI Clock, make sure that a tempo map has been
programmed in the MD4S.
(If the measure/beat display does not appear when you press the
DISPLAY button, a tempo map has not been set.)
Make sure that the MD4S has been set to transmit MTC or MIDI
Clock messages from its MIDI OUT connector. When MTC is being
transmitted, the MTC SYNC MASTER indicator will light. When MIDI
Clock is being transmitted, the MIDI CLK indicator will light.
Make sure that X1/2 Play is turned off. If X1/2 Play is on, synchroni-
zation is not possible.
If you are using a Repeat function such as A-B Repeat, some time
may be required for the MIDI sequencer to synchronize during a
repeat, due to the slowness of the MD4S locate function.
Symptom
Advice