Yamaha MD4S Owner's Manual - Page 47

Applying effects 47 Applying effects during mixdown Applying an effect such as reverb to each track during a mixdown is an example of a situation in which you would connect the external effect processor to the AUX SEND jack. In this case, you can use the AUX control of each input channel to adjust the effect depth for each track. 1 IN OUT THRU MIDI TRACK DIRECT OUT 2TR IN STEREO MONITOR OUT OUT 1 2 AUX SEND 1 2 INSERT I/O MIC/LINE INPUT INSERT I/O 3 4 LINE INPUT 5 6 7 8 4 3 1 GAIN 2 GAIN 3 GAIN 4 GAIN 5/6 7/8 LINE MIC MIC/ LINE PB CUE FLIP P A N L R 0 HIGH L E V E L 10 LINE MIC MIC/ LINE PB CUE FLIP P A N L R 0 HIGH L E V E L 10 LINE MIC MIC/ LINE PB CUE FLIP P A N L R 0 HIGH L E V E L 10 LINE MIC MIC/ LINE PB CUE FLIP P A N L R 0 HIGH L E V E L 10 0 10 0 10 CUE MIX TO STEREO MONITOR SELECT 2TR IN -15 +15 -15 +15 -15 +15 -15 +15 MID MID MID MID -15 +15 -15 +15 -15 +15 -15 +15 LOW LOW LOW LOW -15 +15 -15 +15 -15 +15 -15 +15 AUX AUX AUX AUX STEREO CUE BUS MULTITRACK MD RECORDER 1 2 1 2 1 2 1 2 PAN PAN PAN PAN L R L R L R L R 10 10 10 10 9 9 9 9 8 8 8 8 7 7 7 7 6 6 6 6 5 5 5 5 4 4 4 4 3 3 3 3 2 2 2 2 1 1 1 1 0 0 0 0 MONITOR LEVEL MIN 10 9 8 7 6 5 4 3 2 1 0 MAX 10 9 8 7 6 5 4 3 2 1 0 1 2 3 4 STEREO REPEAT MARK SEARCH AB AUTO PUNCH I/O LAST REC SEARCH IN OUT SONG SEARCH REHE REC PLAY MARK SET PAUSE STOP TOC WRITE CH1 1 L REC SELECT CH2 CH3 2 3 R L CH4 4 R EJECT PEAK HOLD DISPLAY PITCH ADJUST EDIT UTILITY EXIT ENTER DATA CURSOR PHONES PUNCH I/O 5 1 Connect the AUX SEND 1 jack to the input jack of your effect processor, and connect the output jacks of the effect processor to LINE INPUT jacks 5 and 6. Make settings on the effect processor so that its output jacks will output only the effect sound. 2 Prepare for mixdown. As described in "Mixdown" (page 32), adjust the mix balance of each track, and perform the steps leading up to mixdown (steps 1-6). 3 Press the PLAY button to playback the song, and for each input channel to which you wish to apply the effect, rotate the AUX control toward the "1" position. The signals from input channels 1-4 (the playback of tracks 1-4) will be sent to the external effect processor connected to the AUX SEND 1 jack. Adjust the input level of the effect processor if necessary. 4 Raise level control 5/6. The effect sound processed by the external effect processor will be mixed into the ST bus. Raising the level control will increase the overall effect. 5 When you are finished adjusting the effect depth, press the SONG SEARCH [ ] button to locate to the beginning of the song, and begin the mixdown. -Owner's Manual