Yamaha MD4S Owner's Manual - Page 57

Press the PLAY button to begin the actual auto punch-in/out.

Get Yamaha MD4S PDF manuals and user guides View all Yamaha MD4S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Punch-in/out 57 Rehearsing the auto punch-in/out (single-take) 5. Press the PLAY button, and begin rehearsing the auto punch-in/out. When you press the PLAY button, the MD4S will automatically locate to the pre-roll point, and will start playback. When the auto punch-in point is reached, the IN indicator in the display will disappear, and the monitor signal will switch from the track playback to the recording source. When the auto punch-out point is reached the OUT indicator in the display will go dark, and the monitor signal will revert to the track playback. (In rehearsal mode, recording will not actually take place during this time.) After the auto-punch out point is passed and the post-roll is reached, the MD4S will automatically locate to the pre-roll point, and again enter auto punch-in/out rehearsal-pause mode. Tip: When the display shows "A.Punch Rehe," you can begin rehearsing the auto punch-in/ out simply by pressing the PLAY button. (It is not necessary to press the REHE button.) Tip: If you press the REPEAT button while rehearsing auto punch-in/out, the auto punchin/out rehearsal will repeat automatically. Actually performing the auto punch-in/out (single-take) 6. When stopped or paused, press the REC button. The REC indicator will blink, the display will indicate "A.Pnch," and the MD4S will be in auto punch-in/out record-pause mode. 7. Press the PLAY button to begin the actual auto punch-in/out. When you press the PLAY button, the MD4S will automatically locate to the pre-roll point, and begin playback. When you reach the auto punch-in point, the IN indicator of the display will go dark, and the track selected by the REC SELECT buttons will begin recording (punchin). When you reach the auto punch-out point, the OUT indicator of the display will go dark, recording will end, and playback will resume (punch-out). When the post-roll point is reached, auto punch-in/out will automatically be defeated, and the MD4S will locate to the pre-roll point and automatically enter playback-pause mode. 8. Press the PLAY button to hear the recorded result. Note: In the case of single-take auto punch-in/out, auto punch-in/out will automatically be canceled when you perform the actual punch-in/out. If you wish to perform auto punch-in/ out once again, you must repeat the procedure from step 1. Tip: If an optional FC5 foot switch is connected to the PUNCH I/O jack, you can use the foot switch to perform steps 4 and 6. -Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
Punch-in/out
57
—Owner’s Manual
Rehearsing the auto punch-in/out (single-take)
5.
Press the PLAY button, and begin rehearsing the auto punch-in/out.
When you press the PLAY button, the MD4S will automatically locate to the pre-roll point,
and will start playback. When the auto punch-in point is reached, the IN indicator in the dis-
play will disappear, and the monitor signal will switch from the track playback to the record-
ing source. When the auto punch-out point is reached the OUT indicator in the display will
go dark, and the monitor signal will revert to the track playback. (In rehearsal mode, record-
ing will not actually take place during this time.) After the auto-punch out point is passed and
the post-roll is reached, the MD4S will automatically locate to the pre-roll point, and again
enter auto punch-in/out rehearsal-pause mode.
Actually performing the auto punch-in/out (single-take)
6.
When stopped or paused, press the REC button.
The REC indicator will blink, the display will indicate “A.Pnch,” and the MD4S will be in auto
punch-in/out record-pause mode.
7.
Press the PLAY button to begin the actual auto punch-in/out.
When you press the PLAY button, the MD4S will automatically locate to the pre-roll point,
and begin playback. When you reach the auto punch-in point, the IN indicator of the display
will go dark, and the track selected by the REC SELECT buttons will begin recording (punch-
in). When you reach the auto punch-out point, the OUT indicator of the display will go dark,
recording will end, and playback will resume (punch-out). When the post-roll point is
reached, auto punch-in/out will automatically be defeated, and the MD4S will locate to the
pre-roll point and automatically enter playback-pause mode.
8.
Press the PLAY button to hear the recorded result.
Tip:
When the display shows “A.Punch Rehe,” you can begin rehearsing the auto punch-in/
out simply by pressing the PLAY button. (It is not necessary to press the REHE button.)
Tip:
If you press the REPEAT button while rehearsing auto punch-in/out, the auto punch-
in/out rehearsal will repeat automatically.
Note:
In the case of single-take auto punch-in/out, auto punch-in/out will automatically be
canceled when you perform the actual punch-in/out. If you wish to perform auto punch-in/
out once again, you must repeat the procedure from step 1.
Tip:
If an optional FC5 foot switch is connected to the PUNCH I/O jack, you can use the
foot switch to perform steps 4 and 6.