Yamaha RS7000 Owner's Manual - Page 267

2. MIDI Events Handled by the RS7000 4. Control Change (CC) G Panpot (Control Number 010) • Sets the pan position for each individual part. The sound is panned fully left when the value is "0" and fully right when the value is "127". The displayed values are -64 ~ +63. G Expression (Control Number 011) • Sets the expression for each individual part. No sound is pro- duced when the value is "0", and "127" produces maximum volume. This parameter produces volume variations during Control Number Data • Control Change events control voice and effect parameters. • Control Change events are generated when a controller such as a modulation wheel or foot controller is operated on an exter- nal keyboard. • Control numbers 1 - 119 (except for 32) can be recorded in real time by using the assignable knobs. • The control number specifies the controller. • The data specifies the "position" of the controller assigned to the selected control number. The bar graph to the right is a graphic representation of the data value. [Settings] Control Number Data 000 ~ 127 000 ~ 127 playback. G Sustain (Hold 1) (Control Number 064) • This MIDI message represents sustain pedal ON/OFF opera- tions. Notes playing when the pedal is pressed will be sustained. When the value is "0" ~ "63" sustain is OFF, and when the data is "64" ~ "127" sustain is ON. G Portamento (Control Number 065) • This MIDI message turns portamento ON or OFF. When the value is "0" ~ "63" portamento is OFF, and when the data is "64" ~ "127" portamento is ON. • The length (degree) of the portamento effect is controlled by Portamento Time (Control Number 005). G Sostenuto Pedal (Control Number 066) • This MIDI message represents sostenuto pedal ON/OFF operations. When the value is "0" ~ "63" sostenuto is OFF, and when the data is "64" ~ "127" sostenuto is ON. NOTE If the controller data is varied suddenly, the tone generator may produce click noise in some cases. G Harmonic Content (Control Change 071) • Adjusts the resonance of the filter assigned to a voice. The res- onance is adjusted by using the data range of 0 ~ 127 as an offset value with a display range of -64 ~ +63 which is added to the voice data. G Release Time (Control Change 072) Some of the more important control numbers and controllers • Adjusts the release time of the voice AEG. The release time is are listed below. adjusted by using the data range of 0 ~ 127 as an offset value G Modulation Wheel (Control Number 001) with a display range of -64 ~ +63 which is added to the voice 7 • The MIDI data produced when a modulation wheel is operated. data. No modulation is applied when the value is "0", and "127" pro- G Attack Time (Control Change 073) duces maximum modulation. • Adjusts the attack time of the voice AEG. The attack time is G Portamento Time (Control Number 005) adjusted by using the data range of 0 ~ 127 as an offset value • This MIDI message controls the portamento effect. No porta- with a display range of -64 ~ +63 which is added to the voice Other Information mento is produced when the value is "0", and "127" produces maximum portamento time. • Portamento is only produced when Portamento (Control Number 065) is ON. G Data Entry MSB (Control Number 006) G Data Entry LSB (Control Number 038) data. G Brightness (Control Change 074) • Adjusts the cutoff frequency of the filter assigned to a voice. The cutoff is adjusted by using the data range of 0 ~ 127 as an offset value with a display range of -64 ~ +63 which is added to the voice data. • These parameters specify the value of RPN MSB, RPN LSB (Page 268), NRPN MSB, and NRPN LSB events (Page 268). The value is represented by two control change data numbers - the MSB and the LSB. G Volume (Control Number 007) • Sets the volume for each individual part. No sound is produced when the value is "0", and "127" produces maximum volume. RS7000 267