HP 170X HP Jetdirect Print Server 170X Installation and Configuration - Page 49

Using Telnet - jetdirect find ip

Get HP 170X - JetDirect Print Server PDF manuals and user guides
UPC - 882780300699
View all HP 170X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

Using Telnet This subsection describes how to configure the print server using Telnet. Note To use Telnet commands with the HP Jetdirect print server, a route must be available from your workstation to the print server. Simplistically, this means that there must be a match between the network identification of your system to that of the HP Jetdirect print server. On Windows systems, you can use the following route command at a system command prompt to add a route to the print server: route add where is the IP address configured on the HP Jetdirect print server, and is the IP address of the workstation's network card that is attached to the same physical LAN as the print server. ENWW TCP/IP Configuration 3-49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
TCP/IP Configuration 3-49
ENWW
Using Telnet
This subsection describes how to configure the print server
using Telnet.
Note
To use Telnet commands with the HP Jetdirect
print server, a route must be available from
your workstation to the print server.
Simplistically, this means that there must be a
match between the network identification of
your system to that of the HP Jetdirect print
server.
On Windows systems, you can use the following
route
command at a system command prompt
to add a route to the print server:
route add
<IP address Jetdirect
>
<IP address workstation>
where
<IP address Jetdirect
> is the IP
address configured on the HP Jetdirect print
server, and
<IP address workstation>
is
the IP address of the workstation's network
card that is attached to the same physical LAN
as the print server.