HP 170X HP Jetdirect Print Server 170X Installation and Configuration - Page 52

Telnet Configuration Parameter Examples, 52 TCP/IP Configuration

Get HP 170X - JetDirect Print Server PDF manuals and user guides
UPC - 882780300699
View all HP 170X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

4. At the Telnet prompt ">" type: parameter: value then press Enter, where parameter refers to the configuration parameter you are defining, and value refers to the definitions you are assigning to that parameter. See Table 3.3 for examples on assigning configuration parameters. 5. Repeat step 4 to set any additional configuration parameters. 6. When you have finished typing the configuration parameters, type: quit and press Enter to activate the configuration parameters. To exit without activating parameters, type exit and press Enter. Telnet Configuration Parameter Examples The examples in Table 3.3 show how to use Telnet configuration commands. Note If a parameter is supplied by the DHCP server, its value cannot be changed using Telnet without disabling DHCP. 3-52 TCP/IP Configuration ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
3-52 TCP/IP Configuration
ENWW
4.
At the Telnet prompt “
>
” type:
parameter: value
then press
Enter
, where
parameter
refers to the
configuration parameter you are defining, and
value
refers
to the definitions you are assigning to that parameter.
See Table
3.3
for examples on assigning configuration
parameters.
5.
Repeat step 4 to set any additional configuration
parameters.
6.
When you have finished typing the configuration
parameters, type:
quit
and press
Enter
to activate the configuration parameters.
To exit without activating parameters, type
exit
and press
Enter
.
Telnet Configuration Parameter Examples
The examples in Table
3.3
show how to use Telnet configuration
commands.
Note
If a parameter is supplied by the DHCP server,
its value cannot be changed using Telnet
without disabling DHCP.