HP 170X HP Jetdirect Print Server 170X Installation and Configuration - Page 69

HP Jetdirect Configuration Messages 6-69, Table 6.2, General HP Jetdirect Messages 1 of 13 - replacement

Get HP 170X - JetDirect Print Server PDF manuals and user guides
UPC - 882780300699
View all HP 170X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

Table 6.2 General HP Jetdirect Messages (1 of 13) Message Description ARP DUPLICATE IP ADDRESS The ARP layer has detected another node on the network using the same IP address as the HP Jetdirect print server. Extended error information below this message shows the hardware address of the other node. BABBLE ERROR Run the power-on self-test: turn the print server off, then on again. If the error persists, replace the HP Jetdirect print server. For information on replacing your HP Jetdirect print server, see the warranty service information. BAD BOOTP REPLY An error was detected in the BOOTP reply that the HP Jetdirect print server received. The BOOTP reply either had insufficient data in the UDP datagram to contain the minimum BOOTP header of 236 bytes, had an operation field that was not BOOTPREPLY(0X02), had a header field that did not match the print servers hardware address, or had a UDP source port that was not the BOOTP server port (67/udp). BAD BOOTP TAG SIZE The tagsize in a vendor specific field in the BOOTP reply is either 0, or greater than the remaining number of unprocessed bytes in the vendor specified area. BOOTP/DHCP IN PROGRESS The HP Jetdirect print server is currently in the process of obtaining its basic IP configuration information through BOOTP/DHCP, and has not detected any errors. CF ERR - ACCESS LIST The TFTP configuration file specified too many EXCEEDED access list entries using the "allow:" keyword. CF ERR - FILE INCOMPLETE The TFTP configuration file contained an incomplete last line that did not end in a newline character. CF ERR - INVALID PARAM A line in the TFTP configuration file contained an invalid value for one of the parameters on that line. CF ERR - LINE TOO LONG A line being processed in the TFTP configuration file was longer than the HP Jetdirect print server could accept. ENWW HP Jetdirect Configuration Page Messages 6-69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
HP Jetdirect Configuration Page Messages 6-69
ENWW
Table 6.2
General HP Jetdirect Messages (1 of 13)
Message
Description
ARP DUPLICATE IP
ADDRESS
The ARP layer has detected another node on
the network using the same IP address as the
HP Jetdirect print server. Extended error information
below this message shows the hardware address of
the other node.
BABBLE ERROR
Run the power-on self-test: turn the print server off,
then on again. If the error persists, replace the
HP
Jetdirect print server. For information on replacing
your HP Jetdirect print server, see the warranty
service information.
BAD BOOTP REPLY
An error was detected in the BOOTP reply that the
HP Jetdirect print server received. The BOOTP reply
either had insufficient data in the UDP datagram to
contain the minimum BOOTP header of 236 bytes,
had an operation field that was not
BOOTPREPLY(0X02), had a header field that did not
match the print servers hardware address, or had a
UDP source port that was not the BOOTP server port
(67/udp).
BAD BOOTP TAG SIZE
The tagsize in a vendor specific field in the BOOTP
reply is either 0, or greater than the remaining number
of unprocessed bytes in the vendor specified area.
BOOTP/DHCP IN
PROGRESS
The HP Jetdirect print server is currently in the
process of obtaining its basic IP configuration
information through BOOTP/DHCP, and has not
detected any errors.
CF ERR - ACCESS LIST
EXCEEDED
The TFTP configuration file specified too many
access list entries using the “allow:” keyword.
CF ERR - FILE
INCOMPLETE
The TFTP configuration file contained an incomplete
last line that did not end in a newline character.
CF ERR - INVALID
PARAM
A line in the TFTP configuration file contained an
invalid value for one of the parameters on that line.
CF ERR - LINE TOO
LONG
A line being processed in the TFTP configuration file
was longer than the HP Jetdirect print server could
accept.