HP 170X HP Jetdirect Print Server 170X Installation and Configuration - Page 72

HP Jetdirect Configuration Messages, Table 6.2, General HP Jetdirect Messages 4 of 13 - jetdirect warranty

Get HP 170X - JetDirect Print Server PDF manuals and user guides
UPC - 882780300699
View all HP 170X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

Table 6.2 General HP Jetdirect Messages (4 of 13) Message Description INVALID SYSLOG ADDRESS The syslog server IP address specified for the HP Jetdirect print server (through BOOTP) is an invalid IP address for specifying a single node. INVALID TRAP DEST ADDRESS One of the SNMP trap (Trap PDU) destination IP addresses specified for the HP Jetdirect print server (through TFTP) is an invalid IP address for specifying a single node. I/O CARD INITIALIZING The HP Jetdirect print server is initializing the network (INIT) protocols. For more information, see the network protocol status lines on the configuration page. I/O CARD NOT READY There is a problem with the print server or its configuration. Following the I/O CARD NOT READY message is a status message. See this table for a detailed explanation of all status messages. I/O CARD READY The HP Jetdirect print server is connected and awaiting data. LAN ERROR-AUTO REMOVAL Run the power-on self-test: turn the print server off, then on again. If this message reappears on another configuration page, you may have a problem with one of the HP Jetdirect print servers on your network. Check all the print servers on the network for proper operation. LAN ERROR-BABBLE Check the network connections. If the connections are intact, run the power-on self-test: turn the print server off, then on again. If the error persists, replace the HP Jetdirect print server. For replacement instructions, see the warranty service information. LAN ERRORCONTROLLER CHIP Check the network connections. If the connections are intact, run the power-on self-test: turn the print server off, then on again. If the error persists, replace the HP Jetdirect print server. 6-72 HP Jetdirect Configuration Page Messages ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
6-72 HP Jetdirect Configuration Page Messages
ENWW
INVALID SYSLOG
ADDRESS
The syslog server IP address specified for the
HP Jetdirect print server (through BOOTP) is an
invalid IP address for specifying a single node.
INVALID TRAP DEST
ADDRESS
One of the SNMP trap (Trap PDU) destination IP
addresses specified for the HP Jetdirect print server
(through TFTP) is an invalid IP address for specifying
a single node.
I/O CARD INITIALIZING
(INIT)
The HP
Jetdirect print server is initializing the network
protocols. For more information, see the network
protocol status lines on the configuration page.
I/O CARD NOT READY
There is a problem with the print server or its
configuration. Following the I/O CARD NOT READY
message is a status message. See this table for a
detailed explanation of all status messages.
I/O CARD READY
The HP Jetdirect print server is connected and
awaiting data.
LAN ERROR-AUTO
REMOVAL
Run the power-on self-test: turn the print server off,
then on again. If this message reappears on another
configuration page, you may have a problem with one
of the HP Jetdirect print servers on your network.
Check all the print servers on the network for proper
operation.
LAN ERROR-BABBLE
Check the network connections. If the connections
are intact, run the power-on self-test: turn the print
server off, then on again. If the error persists, replace
the HP Jetdirect print server. For replacement
instructions, see the warranty service information.
LAN ERROR-
CONTROLLER CHIP
Check the network connections. If the connections
are intact, run the power-on self-test: turn the print
server off, then on again. If the error persists, replace
the HP Jetdirect print server.
Table 6.2
General HP Jetdirect Messages (4 of 13)
Message
Description