HP 635n HP Jetdirect Print Server Administrator's Guide (Firmware V.36) - Page 145

IPv4 continued, Table 8-7

Get HP 635n - JetDirect IPv6/IPsec Print Server PDF manuals and user guides
UPC - 882780301016
View all HP 635n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 145 highlights

Table 8-7 IPv4 Section (continued) Message Description READY: Indicates the HP Jetdirect print server is awaiting data over TCP/IP. DISABLED: Indicates that TCP/IP was manually disabled. INITIALIZING: Indicates that the print server is searching for the BOOTP server, or trying to get the configuration file through TFTP. An additional status message may also be displayed. An error code and message is displayed if the print server is not ready. For more information, see Table 8-13 Error Messages on page 140. IP ADDRESS The Internet Protocol version 4 (IPv4) address assigned to the HP Jetdirect print server. This is a required entry for operation of the print server on a TCP/IP network. During initialization, a temporary value 0.0.0.0 is displayed. After two minutes, a default IP address 169.254/16 or 192.0.0.192 is assigned. Not Specified: Indicates that an IP address is not assigned or the value is zero. SUBNET MASK The IPv4 subnet mask configured on the HP Jetdirect print server. During initialization, a temporary value 0.0.0.0 is displayed. Depending on configuration parameters, the print server may automatically assign a usable default value. Not Specified: Indicates that a subnet mask is not configured. DEFAULT GATEWAY The IPv4 address of the gateway used when sending packets off the local network. Only one default gateway may be configured. During initialization, a temporary value 0.0.0.0 is displayed. If not provided, the IP address of the Jetdirect print server is used. Not Specified: Indicates that a default gateway is not configured. CONFIG BY: Identifies how the HP Jetdirect print server obtained its IPv4 configuration: BOOTP: Automatic configuration through a BOOTP server. BOOTP/TFTP: Automaticautomatic configuration through a BOOTP server and TFTP configuration file. DHCP: Automatic configuration through a DHCP server DHCP/TFTP: Automatic configuration through a DHCP server and TFTP configuration file. RARP: Automatic configuration through the Reverse Address Resolution Protocol. USER SPECIFIED: Manual configuration through Telnet, the printer's control panel, HP Web Jetadmin, embedded Web server, or other method. DEFAULT IP: The default IP address was assigned. This address may not be a valid address for your network. AUTO IP: A link-local IP address (169.254.x.x) was assigned. If the network is a linklocal network, this address should be valid. NOT CONFIGURED: The print server was not configured with IP parameters. Verify that TCP/IP is enabled, or check for error status. BOOTP SERVER or Displayed if BOOTP, DHCP, or RARP is used for TCP/IP configuration. It specifies the IP address of the system that responds to the HP Jetdirect print server's request for automatic TCP/IP configuration over the network. DHCP SERVER or Not Specified: Indicates that the configuration server's IP address could not be determined or was set to zero in the response packet. RARP SERVER ENWW HP Jetdirect Configuration Page 135

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
Message
Description
READY
: Indicates the HP Jetdirect print server is awaiting data over TCP/IP.
DISABLED
: Indicates that TCP/IP was manually disabled.
INITIALIZING
: Indicates that the print server is searching for the BOOTP server, or
trying to get the configuration file through TFTP. An additional status message may also
be displayed.
An error code and message is displayed if the print server is not ready. For more
information, see
Table
8
-
13
Error Messages
on page
140
.
IP ADDRESS
The Internet Protocol version 4 (IPv4) address assigned to the HP Jetdirect print server.
This is a required entry for operation of the print server on a TCP/IP network. During
initialization, a temporary value 0.0.0.0 is displayed. After two minutes, a default IP
address 169.254/16 or 192.0.0.192 is assigned.
Not Specified
: Indicates that an IP address is not assigned or the value is zero.
SUBNET MASK
The IPv4 subnet mask configured on the HP Jetdirect print server. During initialization,
a temporary value 0.0.0.0 is displayed. Depending on configuration parameters, the
print server may automatically assign a usable default value.
Not Specified
: Indicates that a subnet mask is not configured.
DEFAULT GATEWAY
The IPv4 address of the gateway used when sending packets off the local network. Only
one default gateway may be configured. During initialization, a temporary value 0.0.0.0
is displayed. If not provided, the IP address of the Jetdirect print server is used.
Not Specified
: Indicates that a default gateway is not configured.
CONFIG BY:
Identifies how the HP Jetdirect print server obtained its IPv4 configuration:
BOOTP
: Automatic configuration through a BOOTP server.
BOOTP/TFTP
: Automaticautomatic configuration through a BOOTP server and TFTP
configuration file.
DHCP
: Automatic configuration through a DHCP server
DHCP/TFTP
: Automatic configuration through a DHCP server and TFTP configuration
file.
RARP
: Automatic configuration through the Reverse Address Resolution Protocol.
USER SPECIFIED
: Manual configuration through Telnet, the printer's control panel, HP
Web Jetadmin, embedded Web server, or other method.
DEFAULT IP
: The default IP address was assigned. This address may not be a valid
address for your network.
AUTO IP
: A link-local IP address (169.254.x.x) was assigned. If the network is a link-
local network, this address should be valid.
NOT CONFIGURED
: The print server was not configured with IP parameters. Verify
that TCP/IP is enabled, or check for error status.
BOOTP SERVER
or
DHCP SERVER
or
RARP SERVER
Displayed if BOOTP, DHCP, or RARP is used for TCP/IP configuration. It specifies the
IP address of the system that responds to the HP Jetdirect print server's request for
automatic TCP/IP configuration over the network.
Not Specified
: Indicates that the configuration server's IP address could not be
determined or was set to zero in the response packet.
Table 8-7
IPv4 Section (continued)
ENWW
HP Jetdirect Configuration Page
135