HP 635n HP Jetdirect Print Server Administrator's Guide (Firmware V.36) - Page 189

HP Jetdirect EIO Menu on Classic Control Panel continued, Table C-2

Get HP 635n - JetDirect IPv6/IPsec Print Server PDF manuals and user guides
UPC - 882780301016
View all HP 635n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 189 highlights

Table C-2 HP Jetdirect EIO Menu on Classic Control Panel (continued) Menu Item Description If you specify BOOTP=NO*, DHCP=NO* and AUTO IP=NO*, you can manually set the following TCP/IPv4 parameters from the control panel: ● Each byte of the IPv4 address (IP) ● Subnet Mask (SM) ● Syslog Server (LG) ● Default Gateway (GW) ● Idle Timeout period (default is 270 seconds, 0 disables the timeout) ● CFG DNS 1=YES* will allow you to specify the IPv4 address of a primary DNS server, one byte at a time. ● CFG DNS 2=YES* will allow you to specify the IPv4 address of a secondary DNS server, one byte at a time. ● IPV6 = YES* enables IPv6 operation on the print server. Select NO to disable IPv6 operation. ● POLICY= allows you to select one of the following IPv6 addressing policies for the print server. ● RTR_AV: (default) The stateful auto-configuration method to be used by the print server is determined by a router. The router specifies whether or not the print server is to obtain its address, its configuration information, or both from a DHCPv6 server. ● RTR_UN: If a router is not available, the print server should attempt to obtain its stateful configuration from a DHCPv6 server. ● ALWAYS: Whether or not a router is available, the print server will always attempt to obtain its stateful configuration from a DHCPv6 server. ● MANUAL= KEEP/DISABLE specifies the behavior for a manually-configured IPv6 address detected on the print server. ● KEEP: (default) If configured, maintain the address in an active state. ● DISABLE: If configured, maintain the address but in an inactive state. Print a Jetdirect configuration page to verify your settings. However, note that the print server may overwrite selected parameters with values that ensure proper operation. CFG IPX/SPX Selects whether you want to access the IPX/SPX menu and set IPX/SPX protocol parameters. NO (default): Bypass the IPX/SPX menu items. YES: Access the IPX/SPX menu items. In the IPX/SPX menu, you can specify the Frame Type parameter used on your network. ● AUTO (default) will automatically set and limit the frame type to the first one detected. ● For Ethernet cards, frame type selections include EN_8023, EN_II, EN_8022, EN_SNAP. WEB For configuration management, specify whether the embedded Web server will accept communications using HTTPS (Secure HTTP) only, or both HTTP and HTTPS. HTTPS: For secure, encrypted communications, only HTTPS access is accepted. The print server will appear as a secure site. HTTP/HTTPS: Access using either HTTP or HTTPS is permitted. ENWW Jetdirect EIO Menus for Classic Control Panels 179

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
Menu Item
Description
If you specify
BOOTP=NO*
,
DHCP=NO*
and
AUTO IP=NO*
, you can manually set the
following TCP/IPv4 parameters from the control panel:
●
Each byte of the IPv4 address (IP)
●
Subnet Mask (SM)
●
Syslog Server (LG)
●
Default Gateway (GW)
●
Idle Timeout period (default is 270 seconds, 0 disables the timeout)
●
CFG DNS 1=YES*
will allow you to specify the IPv4 address of a primary DNS server, one
byte at a time.
●
CFG DNS 2=YES*
will allow you to specify the IPv4 address of a secondary DNS server,
one byte at a time.
●
IPV6 = YES*
enables IPv6 operation on the print server. Select NO to disable IPv6 operation.
●
POLICY
=<option> allows you to select one of the following IPv6 addressing policies for the
print server.
●
RTR_AV
: (default) The stateful auto-configuration method to be used by the print
server is determined by a router. The router specifies whether or not the print server
is to obtain its address, its configuration information, or both from a DHCPv6 server.
●
RTR_UN
: If a router is not available, the print server should attempt to obtain its stateful
configuration from a DHCPv6 server.
●
ALWAYS
: Whether or not a router is available, the print server will always attempt to
obtain its stateful configuration from a DHCPv6 server.
●
MANUAL
=
KEEP
/
DISABLE
specifies the behavior for a manually-configured IPv6 address
detected on the print server.
●
KEEP
: (default) If configured, maintain the address in an active state.
●
DISABLE
: If configured, maintain the address but in an inactive state.
Print a Jetdirect configuration page to verify your settings. However, note that the print server
may overwrite selected parameters with values that ensure proper operation.
CFG IPX/SPX
Selects whether you want to access the IPX/SPX menu and set IPX/SPX protocol parameters.
NO
(default): Bypass the IPX/SPX menu items.
YES
: Access the IPX/SPX menu items.
In the IPX/SPX menu, you can specify the
Frame Type
parameter used on your network.
●
AUTO
(default) will automatically set and limit the frame type to the first one detected.
●
For Ethernet cards, frame type selections include EN_8023, EN_II, EN_8022, EN_SNAP.
WEB
For configuration management, specify whether the embedded Web server will accept
communications using HTTPS (Secure HTTP) only, or both HTTP and HTTPS.
HTTPS
: For secure, encrypted communications, only HTTPS access is accepted. The print
server will appear as a secure site.
HTTP/HTTPS
: Access using either HTTP or HTTPS is permitted.
Table C-2
HP Jetdirect EIO Menu on Classic Control Panel (continued)
ENWW
Jetdirect EIO Menus for Classic Control Panels
179