HP 635n HP Jetdirect Print Server Administrator's Guide (Firmware V.36) - Page 155

A Turn Printer Off / On, 5d Dhcp Lease Duration Too

Get HP 635n - JetDirect IPv6/IPsec Print Server PDF manuals and user guides
UPC - 882780301016
View all HP 635n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 155 highlights

Table 8-13 Error Messages (continued) Error Code and Message Description BOOTPREPLY(0X02), had a header field that did not match the print servers hardware address, or had a UDP source port that was not the BOOTP/DHCP server port (67/udp). 53 BAD BOOTP TAG SIZE The tag size in a vendor-specific field in the BOOTP reply is either 0, or greater than the remaining number of unprocessed bytes in the vendor-specified area. 54 BOOTP/RARP IN PROGRESS The HP Jetdirect print server is currently in the process of obtaining its basic IP configuration information through BOOTP/RARP. 55 BOOTP/DHCP IN PROGRESS The HP Jetdirect print server is currently in the process of obtaining its basic IP configuration information through BOOTP/DHCP, and has not detected any errors. 56 DHCP NAK The HP Jetdirect print server received a negative acknowledgement message from the DHCP server in response to a configuration request. 57 UNABLE TO CONNECT DHCP The HP Jetdirect print server had received IP parameters from a DHCP server, but SVR communication with the DHCP server has been lost. Check status of the DHCP server. If an infinite lease was assigned, the print server will use the IP address of the most recent DHCP server used, but operation may be degraded until a DHCP server responds. 58 POSTSCRIPT MODE NOT SELECTED The printer does not support AppleTalk or AppleTalk extensions. 59 INCOMPLETE F/W - MUST DOWNLOAD Firmware download message. Currently downloading firmware to the HP Jetdirect print server, or the download did not complete properly. 5A TURN PRINTER OFF / ON Firmware download message. Download of firmware is complete. Power off/on the HP Jetdirect print server. 5C DHCP BAD REPLY A bad reply was received from the DHCP server. Check your DHCP server settings for this print server. 5D DHCP LEASE DURATION TOO The DHCP lease times for this print server's TCP/IP configuration settings are too short. SHORT Re-configure the DHCP lease times on the DHCP server. 5E DHCP LEASE RELEASED The lease for DHCP-configured parameters, including the IP address, have been released through a manual configuration method, such as through the printer's control panel. 5F WINS REGISTRATION FAILED Attempts to register the print server's name on the WINS server failed. Check for duplicate names, or verify the WINS server configuration. 61 AUTO IP CONFIGURED An IP address could not be retrieved over the network. The print server will default to an IP address using link-local addressing in the form 169.254.x.x. 62 DEFAULT IP CONFIGURED An IP address could not be retrieved over the network. The print server will default to a legacy default IP address 192.0.0.192. 63 AUTO IP IN PROGRESS The print server is automatically assigning an IP address using link-local addressing in the form 169.254.x.x. 64 INVALID PASSWORD An invalid password was specified through TFTP. Verify that the password consists of a maximum of 16 printable characters. 83 DISCONNECTING FROM SERVER The server has been shut down because of a configuration change or reset request. This message automatically clears after a few seconds, unless the printer is offline, is in an error state, or is servicing another I/O port or another network protocol. 84 DHCP LEASE TIMERS ADJUSTED The print server detected a DHCP lease error due to one of the following conditions: ● Renew time is less than 30 seconds. ● Rebind time is less than 52 seconds. ENWW HP Jetdirect Configuration Page 145

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
Error Code and Message
Description
BOOTPREPLY(0X02), had a header field that did not match the print servers hardware
address, or had a UDP source port that was not the BOOTP/DHCP server port (67/udp).
53 BAD BOOTP TAG SIZE
The tag size in a vendor-specific field in the BOOTP reply is either 0, or greater than
the remaining number of unprocessed bytes in the vendor-specified area.
54 BOOTP/RARP IN PROGRESS
The HP Jetdirect print server is currently in the process of obtaining its basic IP
configuration information through BOOTP/RARP.
55 BOOTP/DHCP IN PROGRESS
The HP Jetdirect print server is currently in the process of obtaining its basic IP
configuration information through BOOTP/DHCP, and has not detected any errors.
56 DHCP NAK
The HP Jetdirect print server received a negative acknowledgement message from the
DHCP server in response to a configuration request.
57 UNABLE TO CONNECT DHCP
SVR
The HP Jetdirect print server had received IP parameters from a DHCP server, but
communication with the DHCP server has been lost. Check status of the DHCP server.
If an infinite lease was assigned, the print server will use the IP address of the most
recent DHCP server used, but operation may be degraded until a DHCP server
responds.
58 POSTSCRIPT MODE NOT
SELECTED
The printer does not support AppleTalk or AppleTalk extensions.
59 INCOMPLETE F/W - MUST
DOWNLOAD
Firmware download message. Currently downloading firmware to the HP Jetdirect print
server, or the download did not complete properly.
5A TURN PRINTER OFF / ON
Firmware download message. Download of firmware is complete. Power off/on the HP
Jetdirect print server.
5C DHCP BAD REPLY
A bad reply was received from the DHCP server. Check your DHCP server settings for
this print server.
5D DHCP LEASE DURATION TOO
SHORT
The DHCP lease times for this print server's TCP/IP configuration settings are too short.
Re-configure the DHCP lease times on the DHCP server.
5E DHCP LEASE RELEASED
The lease for DHCP-configured parameters, including the IP address, have been
released through a manual configuration method, such as through the printer's control
panel.
5F WINS REGISTRATION FAILED
Attempts to register the print server's name on the WINS server failed. Check for
duplicate names, or verify the WINS server configuration.
61 AUTO IP CONFIGURED
An IP address could not be retrieved over the network. The print server will default to
an IP address using link-local addressing in the form 169.254.x.x.
62 DEFAULT IP CONFIGURED
An IP address could not be retrieved over the network. The print server will default to a
legacy default IP address 192.0.0.192.
63 AUTO IP IN PROGRESS
The print server is automatically assigning an IP address using link-local addressing in
the form 169.254.x.x.
64 INVALID PASSWORD
An invalid password was specified through TFTP. Verify that the password consists of
a maximum of 16 printable characters.
83 DISCONNECTING FROM
SERVER
The server has been shut down because of a configuration change or reset request.
This message automatically clears after a few seconds, unless the printer is offline, is
in an error state, or is servicing another I/O port or another network protocol.
84 DHCP LEASE TIMERS
ADJUSTED
The print server detected a DHCP lease error due to one of the following conditions:
●
Renew time is less than 30 seconds.
●
Rebind time is less than 52 seconds.
Table 8-13
Error Messages (continued)
ENWW
HP Jetdirect Configuration Page
145