HP 635n HP Jetdirect Print Server Administrator's Guide (Firmware V.36) - Page 62

SNMP Traps, DHCP Renew Time

Get HP 635n - JetDirect IPv6/IPsec Print Server PDF manuals and user guides
UPC - 882780301016
View all HP 635n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Table 3-3 Telnet Commands and Parameters (continued) DHCP Renew Time (Read-only parameter) DHCP T1 timeout, specifying the DHCP lease renewal time (seconds). DHCP Rebind Time (Read-only parameter) DHCP T2 timeout, specifying the DHCP lease rebind time (seconds). SNMP snmp-config get-cmnty-name set-cmnty-name Enables or disables SNMP operation on the print server. CAUTION: Disabling SNMP will disable all SNMP agents (SNMP v1, v2, v3) as well as communications with management applications, such as HP Web Jetadmin. In addition, firmware upgrades through current HP downloading utilities will be disabled. 0 disables, 1 (default) enables SNMP. Specifies a password that determines which SNMP GetRequests the HP Jetdirect print server will respond to. This is optional. If a user-specified get community name is set, the print server will respond to either a user-specified community name or the factory-default. The community name must be ASCII characters. The maximum length is 255 characters. Specifies a password that determines which SNMP SetRequests (control functions) the HP Jetdirect print server will respond to. The community name of an incoming SNMP SetRequest must match the print server's "set community name" for the print server to respond. (For additional security, you may limit configuration access through the print server's host access list.) Community names must be ASCII characters. The maximum length is 255 characters. default-get-cmnty SNMP Traps auth-trap trap-dest Enables or disables the default Get community name. 0 disables. 1 (default) enables. Disabling this parameter may prohibit communications with SNMP management applications. Configures the print server to send (on) or not send (off) SNMP authentication traps. Authentication traps indicate that an SNMP request was received, but the community name check failed. . 0 is off. 1 (default) is on Enters a host IP address into the HP Jetdirect print server's SNMP trap destination list. The command format is: trap-dest: [community name] [port number] Where is the IP address of the host to receive traps, [community name] specifies the SNMP community name, and [port number] identifies the port number to use. The default community name is 'public'; the default SNMP port number is '162'. The port number cannot be specified without a community name. To delete the list, use trap-dest: 0. 52 Chapter 3 TCP/IP Configuration ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
DHCP Renew Time
(Read-only parameter) DHCP T1 timeout, specifying the DHCP lease renewal time
(seconds).
DHCP Rebind Time
(Read-only parameter) DHCP T2 timeout, specifying the DHCP lease rebind time
(seconds).
SNMP
snmp-config
Enables or disables SNMP operation on the print server.
CAUTION:
Disabling SNMP will disable all SNMP agents (SNMP v1, v2, v3) as
well as communications with management applications, such as HP Web
Jetadmin. In addition, firmware upgrades through current HP downloading utilities
will be disabled.
0
disables,
1
(default) enables SNMP.
get-cmnty-name
Specifies a password that determines which SNMP GetRequests the HP Jetdirect print
server will respond to. This is optional. If a user-specified get community name is set, the
print server will respond to either a user-specified community name or the factory-default.
The community name must be ASCII characters. The maximum length is 255 characters.
set-cmnty-name
Specifies a password that determines which SNMP SetRequests (control functions) the
HP Jetdirect print server will respond to. The community name of an incoming SNMP
SetRequest must match the print server's “set community name” for the print server to
respond. (For additional security, you may limit configuration access through the print
server's host access list.) Community names must be ASCII characters. The maximum
length is 255 characters.
default-get-cmnty
Enables or disables the default Get community name.
0
disables.
1
(default) enables.
Disabling this parameter may prohibit communications with SNMP management
applications.
SNMP Traps
auth-trap
Configures the print server to send (on) or not send (off) SNMP authentication traps.
Authentication traps indicate that an SNMP request was received, but the community name
check failed. .
0
is off.
1
(default) is on
trap-dest
Enters a host IP address into the HP Jetdirect print server's SNMP trap destination list.
The command format is:
trap-dest: <ip-address> [community name] [port number]
Where
<ip-address>
is the IP address of the host to receive traps,
[community
name]
specifies the SNMP community name, and
[port number]
identifies the port
number to use.
The default community name is ‘public’; the default SNMP port number is ‘162’. The port
number cannot be specified without a community name.
To delete the list, use
trap-dest: 0
.
Table 3-3
Telnet Commands and Parameters (continued)
52
Chapter 3
TCP/IP Configuration
ENWW