HP 635n HP Jetdirect Print Server Administrator's Guide (Firmware V.36) - Page 185

Menu item, Sub-menu item, Values and Description, Data gathered from the HTTP, SNMP, and Data Path

Get HP 635n - JetDirect IPv6/IPsec Print Server PDF manuals and user guides
UPC - 882780301016
View all HP 635n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 185 highlights

Table C-1 Jetdirect EIO Menu on Graphical Control Panel (continued) Menu item Sub-menu item Sub-menu item Values and Description Yes: Choose this test. No: Do not choose this test. SNMP Test This test checks operation of SNMP communications by accessing predefined SNMP objects on the device. Yes: Choose this test. No: Do not choose this test. Data Path Test This test helps to identify data path and corruption problems on an HP postscript level 3 emulation device. It sends a predefined PS file to the device, However, the test is paperless; the file will not print. Yes: Choose this test. No: Do not choose this test. Select All Tests Select this item to run all the embedded tests. Yes: Run all tests, No: Do not run all tests. Execution Time [H] Use this item to specify the length of time (in hours) that an embedded test will be run. You can select a value from 1 to 60 hours. If you select zero (0), the test runs indefinitely until an error occurs or device is turned off. Data gathered from the HTTP, SNMP, and Data Path tests is printed after the tests have completed. Execute No (default): Do not run the selected tests. Yes: Initiate the selected tests. Ping Test This test is used to check network communications. This test sends link-level packets to a remote network host, then waits for an appropriate response. Dest Type Specify whether the target device is an IPv4 or IPv6 node. Dest IPv4 Type the IPv4 address. Dest IPv6 Type the IPv6 address. Packet Size Specify the size of each packet, in bytes, to be sent to the remote host. The minimum is 64 (default) and the maximum is 2048. Timeout Specify the length of time, in seconds, to wait for a response from the remote host. The default is 1 and the maximum is 100. Count Specify the number of ping test packets to send for this test. Select a value from 1 to 100. To configure the test to run continuously, select 0. Print Results If the ping test was not set for continuous operation, you can choose to print the test results. Yes: Print the test results. ENWW Jetdirect Menus for Graphical Control Panels 175

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
Menu item
Sub-menu item
Sub-menu item
Values and Description
Yes
: Choose this test.
No
: Do not choose this test.
SNMP Test
This test checks operation of SNMP communications
by accessing predefined SNMP objects on the device.
Yes
: Choose this test.
No
: Do not choose this test.
Data Path Test
This test helps to identify data path and corruption
problems on an HP postscript level 3 emulation device.
It sends a predefined PS file to the device, However,
the test is paperless; the file will not print.
Yes
: Choose this test.
No
: Do not choose this test.
Select All Tests
Select this item to run all the embedded tests.
Yes
: Run all tests,
No
: Do not run all tests.
Execution Time [H]
Use this item to specify the length of time (in hours) that
an embedded test will be run. You can select a value
from 1 to 60 hours. If you select zero (0), the test runs
indefinitely until an error occurs or device is turned off.
Data gathered from the HTTP, SNMP, and Data Path
tests is printed after the tests have completed.
Execute
No
(default): Do not run the selected tests.
Yes
: Initiate the selected tests.
Ping Test
This test is used to check network communications.
This test sends link-level packets to a remote network
host, then waits for an appropriate response.
Dest Type
Specify whether the target device is an IPv4 or IPv6
node.
Dest IPv4
Type the IPv4 address.
Dest IPv6
Type the IPv6 address.
Packet Size
Specify the size of each packet, in bytes, to be sent to
the remote host. The minimum is 64 (default) and the
maximum is 2048.
Timeout
Specify the length of time, in seconds, to wait for a
response from the remote host. The default is 1 and
the maximum is 100.
Count
Specify the number of ping test packets to send for this
test. Select a value from 1 to 100. To configure the test
to run continuously, select 0.
Print Results
If the ping test was not set for continuous operation,
you can choose to print the test results.
Yes
: Print the test results.
Table C-1
Jetdirect EIO Menu on Graphical Control Panel (continued)
ENWW
Jetdirect Menus for Graphical Control Panels
175