HP Portable 386 Compaq Portable 386 Personal Computer Maintenance and Service - Page 96

Mass Storage Device Assembly

Get HP Portable 386 - Notebook PC PDF manuals and user guides View all HP Portable 386 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 96 highlights

Chapter 8.16 Mass Storage Device Assembly To remove the mass storage device subassembly: 1. Complete the preparation procedure (see Section 8.2). 2. Remove the rear panel (see Section 8.4). 3. To remove the drive bezel, place your thumb on the rear side of the drive bezel. 4. Pull the drive bezel away from the computer with your thumb. (Figure 8-38). 5. Disconnect the following cables (shown in Figure 8-39) from the system board: o Diskette drive data cable o Diskette drive power cable o Fixed disk drive data cable o Fixed disk drive power cable

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
Chapter 8.16 Mass Storage Device Assembly
To remove the mass storage device subassembly:
1. Complete the preparation procedure (see Section 8.2).
2. Remove the rear panel (see Section 8.4).
3. To remove the drive bezel, place your thumb on the rear side of the
drive bezel.
4. Pull the drive bezel away from the computer with your thumb.
(Figure 8-38).
5. Disconnect the following cables (shown in Figure 8-39) from the system
board:
o Diskette drive data cable
o Diskette drive power cable
o Fixed disk drive data cable
o Fixed disk drive power cable