HP Portable 386 Compaq Portable 386 Personal Computer Maintenance and Service - Page 99

Fixed Disk Drive, Locate the fixed disk drive mounted in the rear position

Get HP Portable 386 - Notebook PC PDF manuals and user guides View all HP Portable 386 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 99 highlights

To replace the mass storage device subassembly, reverse steps 7 and 8 CAUTION When replacing the mass storage device subassembly, be sure that the cables do not interfere with the mass storage device enclosure Reconnect the cables, listed in step 5, to the system board. To replace the bezel and rear panel, reverse steps 1 through 4. Chapter 8.17 Fixed Disk Drive To remove the fixed disk drive assembly: 1. Complete the preparation procedure (see Section 8.2). 2. Remove the rear panel (see Section 8.4). 3. Remove the mass storage device subassembly (see Section 8.12). 4. Locate the fixed disk drive (Figure 8-43) mounted in the rear position of the mass storage device subassembly (Drive Position 2). 5. Disconnect the fixed disk drive power and data cables from the fixed disk drive (Figure 8-44).

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
To replace the mass storage device subassembly, reverse steps 7 and 8.
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
CAUTION
When replacing the mass storage device subassembly, be sure that the cables do
not interfere with the mass storage device enclosure.
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
Reconnect the cables, listed in step 5, to the system board.
To replace the bezel and rear panel, reverse steps 1 through 4.
Chapter 8.17 Fixed Disk Drive
To remove the fixed disk drive assembly:
1. Complete the preparation procedure (see Section 8.2).
2. Remove the rear panel (see Section 8.4).
3. Remove the mass storage device subassembly (see Section 8.12).
4. Locate the fixed disk drive (Figure 8-43) mounted in the rear position of
the mass storage device subassembly (Drive Position 2).
5. Disconnect the fixed disk drive power and data cables from the fixed disk
drive (Figure 8-44).